ISO 5753 TAPER MOUNTING

Tapered Bore (1:12 K / 1:30 K30) Clearance Calculator

Calculate axial drive-up distance, radial clearance reduction, and residual mounted clearance for spherical roller bearings and NN30/NNU49 precision spindles—with automatic 240/241 K30 safety interlock.

1. Bearing Series, Bore and Mounting Inputs

1:12 K / 1:30 K30 Interlocked
Tip: For heavy-duty spherical roller bearings, check feeler gauge readings across both roller rows before and after tightening.

2. Axial Drive-Up and Residual Clearance Output

Feeler Verification Aid
Estimated Axial Drive-Up s
—
—
Clearance Reduction Δr
—
—
Residual Mounted Clearance
—
—
Active Bore Taper
—
—
ISO 5753 Unmounted Bands (for bore d)—
Matched Sleeve / Seat Standard—
Reference Min. Residual Clearance—
Verify with ZQM Copied to clipboard

ISO 5753 Tapered Bore Spherical Roller Clearance Table

Unmounted radial internal clearance (μm) and solid-shaft mounting guidance for bores from 30 mm to 630 mm (the calculator above supports 30–1,000 mm).

ISO 5753-1 Table 5 — Tapered Bore Spherical Roller Bearings

30–630 mm Table (Tool: 30–1,000 mm)
Bore d (mm)CN (μm)C3 (μm)C4 (μm)Rec. Δr (mm)s · 1:12 K (mm)s · 1:30 K30 (mm)
30 – 4035 – 5050 – 6565 – 850.020 – 0.0250.30 – 0.38—
40 – 5045 – 6060 – 7575 – 950.025 – 0.0300.38 – 0.45—
50 – 6555 – 7575 – 9595 – 1200.030 – 0.0400.45 – 0.60—
65 – 8070 – 9595 – 120120 – 1500.040 – 0.0500.60 – 0.75—
80 – 10080 – 110110 – 140140 – 1800.045 – 0.0600.68 – 0.901.70 – 2.25
100 – 120100 – 135135 – 170170 – 2200.050 – 0.0700.75 – 1.051.90 – 2.65
120 – 140120 – 160160 – 200200 – 2600.065 – 0.0900.98 – 1.352.45 – 3.40
140 – 160130 – 180180 – 230230 – 3000.075 – 0.1001.13 – 1.502.80 – 3.75
160 – 180140 – 200200 – 260260 – 3400.080 – 0.1101.20 – 1.653.00 – 4.15
180 – 200160 – 220220 – 290290 – 3700.090 – 0.1301.35 – 1.953.40 – 4.90
200 – 225180 – 250250 – 320320 – 4100.100 – 0.1401.50 – 2.103.75 – 5.25
225 – 250200 – 270270 – 350350 – 4500.110 – 0.1501.65 – 2.254.15 – 5.65
250 – 280220 – 300300 – 390390 – 4900.120 – 0.1701.80 – 2.554.50 – 6.40
280 – 315240 – 330330 – 430430 – 5400.130 – 0.1901.95 – 2.854.90 – 7.15
315 – 355270 – 360360 – 470470 – 5900.150 – 0.2102.25 – 3.155.65 – 7.90
355 – 400300 – 400400 – 520520 – 6500.170 – 0.2302.55 – 3.456.40 – 8.65
400 – 450330 – 440440 – 570570 – 7200.200 – 0.2603.00 – 3.907.50 – 9.75
450 – 500370 – 490490 – 630630 – 7900.210 – 0.2803.15 – 4.207.90 – 10.50
500 – 560410 – 540540 – 680680 – 8700.240 – 0.3203.60 – 4.809.00 – 12.00
560 – 630460 – 600600 – 760760 – 9800.260 – 0.3503.90 – 5.259.75 – 13.15

Note: Estimated axial drive-up assumes a solid steel shaft (radial expansion factor k ≈ 0.80, i.e., s ≈ 15×Δr for 1:12 K and s ≈ 37.5×Δr for 1:30 K30). For hollow shafts, thick sleeves, or high-temperature equipment, always verify final residual clearance directly with calibrated feeler gauges or dial indicators.

Tapered Bore Mounting FAQ

Preventing costly mounting errors between 1:12 (K) and 1:30 (K30) bearings.

Which spherical roller bearing series use a 1:30 (K30) taper instead of 1:12 (K)?

ISO wide spherical roller series 240 and 241 use a 1:30 tapered bore designated K30 (paired with AH240/AH241 withdrawal sleeves). All other standard spherical roller series (222, 223, 230, 231, 232, 239) and NN30/NNU49 machine tool spindle bearings use a 1:12 tapered bore (K).

Why is the solid-shaft axial drive-up ratio roughly 15:1 rather than 12:1 for a 1:12 taper?

As the inner ring is pushed up a 1:12 taper, radial interference is split between inner-ring raceway expansion (~80% on a solid steel shaft) and shaft elastic compression (~20%). Therefore Δr ≈ 0.80 × (s / 12) = s / 15, meaning roughly 1.5 mm of axial drive-up produces 0.10 mm of radial clearance reduction.

What happens if I mount a tapered bore bearing onto a hollow CNC spindle?

A hollow spindle wall compresses radially much more than a solid shaft, lowering the expansion efficiency k below 0.80. Consequently, more axial drive-up s is required to reach the same Δr—which is why precision NN30..K spindles must always be verified with a dial indicator and ground spacer ring.

Can cylindrical roller NJ or NU bearings use this tapered bore calculator?

Standard single-row NJ, NU, and NUP cylindrical roller bearings have cylindrical bores and do not use K tapered sleeves. This tool applies strictly to tapered-bore spherical roller bearings (K / K30) and tapered-bore double-row cylindrical spindle bearings (NN30..K / NNU49..K).

ENGINEERING SUPPORT

Ordering K or K30 Bearings with Matched C3 / C4 Clearance?

Send your bore size, sleeve series, and target clearance group to ZQM Bearings for factory stock check and drawing confirmation.

Scroll to Top