Legacy Bearing Codes & Non-Standard Cross-Reference Traps: 116756, KH & FCD

Maintenance storerooms and legacy OEM bills of materials are filled with discontinued numeric designations—such as 116756, 53556KH, 3053180KH, 4053136KH, 42326EH, and 314719C. Blindly typing an old part number into a generic web lookup without checking bore taper ratios, cage styles, or fractional millimeter outer diameters is one of the fastest ways to order a bearing that physically jams in the housing.

Using designation references from ZQM’s General Catalogue, this guide explains four cross-reference traps. Verify dimensions and configuration against the drawing before ordering.

Horizontal length measuring machine checking a bearing ring outside diameter
Horizontal length measurement of a bearing ring. Confirm the specified outside diameter and housing-fit tolerances before replacement.

Top Cross-Reference Traps Every Industrial Buyer Must Check

Nominal ISO boundary dimensions alone do not tell the whole story—especially across non-standard outside diameters, subtle suffix shifts between 1:12 and 1:30 bore tapers, and rolling mill roll-neck variants:

Trap 1: Fractional Non-Standard OD (116756)

  • 116756 translates to QJF1058MB (280 × 419.5 × 65 mm)
  • 419.5 mm outside diameter vs. standard 420 mm QJ series
  • A 0.5 mm outside-diameter difference requires a housing-fit and tolerance review
  • Cylindrical bore design—do NOT assume tapered K bore

Trap 2: KH Suffixes Split 1:12 K vs 1:30 K30

  • 53556KH -> 22256CA/W33; 3053180KH -> 23080CA/W33 (K = 1:12 taper)
  • 4053136KH -> 24036 CA/W33; Series 240/241 taper is 1:30 (K30)
  • Legacy suffixes do not replace verification of the specified bore taper and matching sleeve
  • Do not combine mismatched bore and sleeve tapers; confirm the specified mounting arrangement

Trap 3: EH Suffix vs NJ/NU Locating & Straight Bore

  • 42326EH maps to NJ326EM; 32626EH maps to NU2326EM
  • NJ series is cylindrical bore + one-direction axial location only
  • Never label NJ bearings as bidirectional or tapered K bore
  • Verify Fw and ring compatibility against the drawing for the exact designation

Trap 4: Rolling Mill FCD vs FCDP…YA3 Crosses

  • SKF BC4-0100 / 314719C referenced against FCD5678275
  • Boundary envelope: 280 × 390 × 275 mm, Fw = 308 mm
  • Pin-type hollow-roller FCDP 5678275/YA3 requires print check
  • Verify oil grooves, spacer rings & heat-treatment grade—never direct-swap blindly

Verified Legacy-to-Modern ZQM Designation Cross-Reference Table

The table below reflects printed relationships recorded directly in the ZQM General Catalogue and verified product pages. Treat cross-references as candidate designation matches, not automatic drop-in replacements. Verify dimensions, clearance, cage and lubrication details against your drawing:

Legacy / OEM Ref Modern ZQM Catalogue Code Catalogue d×D×B (mm) Cr / C0r (kN) Critical Warning & Bore / Housing Catch
116756 QJF1058MB (Product) 280 × 419.5 × 65 553 / 1,060 Non-standard 419.5 mm OD (not 420 mm); cylindrical bore; machined brass MB
53556KH 22256 CA/W33 280 × 500 × 130 2,280 / 3,650 Machined brass CA; tapered bore variant uses 1:12 K sleeve
3053180KH 23080 CA/W33 400 × 600 × 148 2,970 / 5,900 146 kg; W33 groove; 1:12 K taper option
3053184KH 23084 CA/W33 420 × 620 × 150 2,910 / 5,850 151 kg; Da max 598 mm; verify legacy K taper on journal
4053136KH 24036 CA/W33 180 × 280 × 100 965 / 1,750 Series 240 tapered variant is 1:30 K30 (22.7 kg); not 1:12 K
42326EH NJ326EM 130 × 280 × 58 615 / 735 Straight cylindrical bore; Fw = 167 mm; one-direction location only
BC4-0100 / 314719C FCD5678275 280 × 390 × 275 Confirm exact configuration Rolling mill 4-row cylindrical; confirm FCD solid vs. FCDP…YA3 pin cage & specs
FCD and FCDP are separate configurations. Confirm the exact designation, cage, load ratings and mounting drawing before substitution.
ZQM factory-boxed spherical roller bearing displaying outer-ring W33 oil groove, lubrication hole, and precision steel cage
Finished W33 spherical roller bearing paired with serialized ZQM factory packaging and stamped designation records.

Case Deep Dive: Why 116756 (QJF1058MB) Requires an Outside-Diameter and Housing-Fit Check

Among all non-standard industrial replacements, 116756 (QJF1058MB) generates the costliest procurement errors. Looking solely at its 280 mm bore and 65 mm width makes it appear close to standard Series 10xx four-point contact ball bearings—yet its printed catalogue outside diameter is exactly 419.5 mm rather than 420.0 mm. A nominal 419.5 mm outside diameter must not be treated as interchangeable with 420.0 mm. Confirm the specified housing fit and tolerances before installation; the diameter difference alone does not establish the actual interference fit.

For a non-standard replacement, confirm outside diameter, split-ring geometry, chamfers and housing tolerances against the agreed drawing before dispatch.

4-Point Cross-Reference Verification Checklist Before Ordering

  • Measure the Actual Physical Housing & Shaft First: Especially on 116756 / QJF1058MB or vintage mill chocks, measure the bearing outside diameter and housing bore using equipment suitable for the specified tolerances before finalizing PO codes.
  • Separate 1:12 K From 1:30 K30 Legacy Prints: Confirm whether legacy KH series belongs to Series 222/230/231/232 (1:12) or Series 240/241 (1:30 K30).
  • Verify Cylindrical Bore & Locating Rib Geometry: Check 42xxx vs. 32xxx legacy cylindrical prefixes so NJ (one-direction locating) never ships where NU floating travel is required.
  • Request Nominal vs. Operational Drawing Confirmation: When swapping competitor codes (such as SKF BC4-0100 / 314719C), send roll-neck tolerances and oil-hole details for written factory confirmation.

Decoding an Old Bearing Stamping or Mixed Cross-Reference BOM?

Upload your legacy part list, physical shaft/housing measurements, or OEM print to ZQM’s application engineering desk for designation, dimensional and configuration verification.

Verify Legacy Cross-Reference

Scroll to Top