QJF10 SERIES · FOUR-POINT CONTACT BALL BEARING
QJF1058MB Four-Point Contact Ball Bearing Dimensions & Specifications
QJF1058MB four-point contact ball bearing: 280 mm bore (d), 419.5 mm outside diameter (D), 65 mm width (B). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings. Note: Specific split-ring configuration (inner vs. outer ring) for QJF designations is confirmed per engineering drawing.
| Bore d | 280 mm |
|---|---|
| Outside diameter D | 419.5 mm |
| Width B | 65 mm |
| Mass | 33.6 kg |
| Catalogue dynamic load Cr | 553 kN |
| Catalogue static load Cor | 1060 kN |
| Grease-lubricated speed | 950 rpm |
| Oil-lubricated speed | 1400 rpm |
Mounting dimensions & additional parameters (10)
| Abutment dimension Da | 402 mm |
|---|---|
| Abutment dimension da | 298 mm |
| Minimum chamfer r12 | 4.0 mm |
| Factor X | 0.6 |
| Factor Y0 | 0.58 |
| Factor Y1 | 0.66 |
| Factor Y2 | 1.07 |
| Factor e | 0.95 |
| Maximum fillet ra | 3 mm |
| Load centre dimension a | 245 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 116756 | ZQM Catalogue P.51 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
How does QJF1058MB relate to legacy code 116756 and standard 420 mm QJ bearings?
In the ZQM General Catalogue (Page 51), QJF1058MB is printed on the same row as legacy reference code 116756 with nominal dimensions 280 × 419.5 × 65 mm. Note that its 419.5 mm outside diameter (D) is 0.5 mm smaller than standard 420 mm OD QJ1056 bearings — verify the housing bore and engineering drawing before ordering.
Which mounting dimensions are listed for QJF1058MB?
The QJF1058MB catalogue lists da min = 298 mm; Da max = 402 mm; ra max = 3 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for QJF1058MB?
The listed values for QJF1058MB are grease: 950 rpm; oil: 1400 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
How should QJF1058MB four-point contact ball bearing be loaded and mounted?
QJF1058MB (280 × 419.5 × 65 mm) is designed for pure axial or predominantly axial bidirectional loads. When paired with a cylindrical roller bearing strictly as an axial locating unit, provide radial clearance between the outer ring and housing bore so it carries no radial load. Confirm specific split-ring configuration (inner vs. outer ring) for this QJF designation per drawing.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
DIRECT FACTORY SOURCING
Request a Quote for QJF1058MB
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

