29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath

Vertical hydro-turbine thrust pedestals, rotary crusher mainshafts, extruder screws, and heavy marine thruster drives demand thrust capacities far beyond flat-roller or angular-contact ball units—especially when shaft deflection cannot be held below half a degree. A 29000 series spherical roller thrust bearing solves both problems simultaneously by combining a steep ~45–50° contact angle with a self-aligning spherical housing-washer raceway (~2–3° misalignment capability).

Engineering cross-section schematic of 29000 series spherical roller thrust bearing showing spherical housing washer raceway, shaft washer, and inner-to-outer centrifugal oil flow
Steep ~45–50 deg contact geometry pumps oil centrifugally outward from the inner bore zone (d / D1) toward the outer perimeter (d1 / D) during vertical operation.

292 vs 293 vs 294 Cross-Section Series & Combined-Load Physics

Unlike radial spherical assemblies, every 29000 series spherical roller thrust bearing carries a single primary axial thrust load Fa alongside a subordinate radial load (typically restricted to Fr <= 0.55 × Fa) on a strictly straight cylindrical bore. Selecting among the three ISO dimension series depends on axial height H and radial section width:

Series Progression & Critical Operating Boundaries
292, 293 & 294 Dimension Series
Straight bore ONLY · Overall height defined by H
  • 292 Series: Lightest cross-section height H for compact vertical pump pedestals with moderate axial thrust.
  • 293 Series: Medium-heavy balance for mill drives and gear reducers (e.g., 29326E, 130 × 225 × 58 mm H).
  • 294 Series: Extra-heavy duty for extreme crushers and extruders (e.g., 29426-EM, 130 × 270 × 85 mm H).
Oil-Bath Pumping & Radial Partnering
Centrifugal oil flow + radial guide unit
  • Tilted rollers pump oil outward from shaft washer OD d1 toward outer diameter D—ideal for circulating oil cooling.
  • If radial shock exceeds 0.55 × Fa or reverses axial direction, pair with a radial unit such as 23080 CA/W33.

Verified ZQM Dimensions: 29324, 29326E & 29426-EM

The table below summarizes verified envelope dimensions, overall height H, washer heights B and C, self-aligning center S, abutment shoulders, and limiting speeds from the ZQM catalogue database (ISO 104 (with radial companion 23080 CA/W33 under ISO 15) boundary series; note that catalog load items whose dynamic/static axial Ca / C0a rating definitions require source drawing confirmation and final cage material execution on 29326E/29426-EM are confirmed per engineering drawing upon order):

Series / Model (Straight Bore) d × D × H & Geometry (B / C / S / d1 / D1) Abutments, Speeds, Mass & Load Verification
29324 (ZQM Catalog (29324)) 120 × 210 × 54 mm (H=54, B=34, C=27, S=70, d1=187.5, D1=156.5 mm) da >= 160, Da = 2.1, ra <= 2 mm · 1,100/1,600 rpm · 7.3 kg · Ref load 645/2,100 kN (verify drawing)
29326E (293 base spec) 130 × 225 × 58 mm (H=58, B=36.5, C=28, S=76, d1=200, D1=166 mm) da >= 170, Da = 2.1, ra <= 2 mm · 1,000/1,500 rpm · 8.48 kg · Ref load 740/2,450 kN (verify drawing)
29426-EM (294 base spec) 130 × 270 × 85 mm (H=85, B=31, C=39.7, S=81, d1=246, D1=183 mm) da >= 195, Da = 4, ra <= 3 mm · 850/1,200 rpm · 28.3 kg · Ref load 1,330/3,900 kN (verify drawing)
23080 CA/W33 (Radial partner example) 400 × 600 × 148 mm (B=148 mm, e=0.23, Y0=2.9, Y1=3, Y2=4.4) da >= 422, Da = 5, ra <= 4 mm · 480/600 rpm · 146 kg · Cr 2,970 / Cor 5,900 kN

Pedestal Support, Minimum Axial Load & Oil-Bath Inspection

Three installation practices prevent catastrophic roller skidding and seat cracking on any 29000 series spherical roller thrust bearing:

  • Verify Rigid Seat Radial & Axial Backing: Under full thrust, the stationary washer develops high hoop stress and requires continuous radial and axial support in a rigid steel or cast-iron pedestal—never mount a heavy 294 unit inside a thin split casing without circumferential backing. Machine shaft shoulder da and seat shoulder Da strictly inside listed limits (e.g., da >= 195 mm, Da <= 225 mm on 29426).
  • Enforce Spring-Loaded Minimum Axial Load (Fa_min): During idle startup or light-load coasting, centrifugal force flings the asymmetrical barrel rollers radially outward against the shaft washer rib unless a minimum axial preload keeps every roller in pure rolling contact. Install calibrated coil or disc springs under the retaining ring on vertical shafts with zero-load starts.
  • Choose Circulating Oil Over Grease Whenever Feasible: Because centrifugal pumping pushes lubricant from d1 toward D, grease channels rapidly away from the inner raceway above vertical-shaft or high n·dm continuous duty. Design an oil-bath sump with upper return channels above the stationary washer or continuous filtered oil circulation (ISO VG 150 to VG 320 depending on sump temperature).

In industrial vertical machinery, choosing between 292, 293, and 294 sections also determines housing envelope and cooling strategy. Compact 292 units fit low-headroom vertical condensate pumps, whereas 293 units such as 29326E (225 mm OD, 58 mm height H, 8.48 kg) handle medium-heavy pulverizers and vertical mill drives. When thrust surges under rock crushing or polymer extrusion pressures, stepping up to 29426-EM (270 mm OD, 85 mm H, 28.3 kg) expands axial reserve while requiring sturdier radial housing walls and dedicated oil circulation.

Pre-Order & Commissioning Check Engineering Target / Parameter Operational Protection
1. Overall Height (H) & Offset (S) Verify H = 58 mm (29326) or 85 mm (29426) plus S = 76 / 81 mm Aligns vertical rotor elevation and spherical seat pivot center
2. Washer Bore & OD Clearances Shaft washer interference fit; stationary washer outer clearance in seat Allows self-aligning tilt up to ~2–3° without pinching the outer ring
3. Oil Sump Level & Cooler Return Static oil level covering roller center; upper-to-lower return ducts bypassing D / d1 back to the inner sump Uses natural inner-to-outer (d/D1 toward d1/D) pumping for continuous circulation for continuous heat removal
4. Load & Cage Confirmation Confirm axial Fa, radial Fr <= 0.55 Fa, and final cage execution per drawing Confirms Ca / C0a rating definitions and cage execution against the manufacturing drawing before manufacturing release

Frequently Asked Questions

Why is oil-bath or circulating oil lubrication preferred over grease on a 29000 series spherical roller thrust bearing?

The ~45–50° inclined rollers act like a centrifugal pump, driving lubricant outward from the inner bore zone (d / D1) toward the outer diameter (d1 / D). Circulating oil continuously replenishes the inner contact zone and removes friction heat, whereas grease tends to be expelled outward at moderate speeds.

What happens if a vertical shaft starts with insufficient axial load on a 293 or 294 thrust assembly?

Without sufficient minimum axial load Fa_min, centrifugal forces overcome rolling traction and cause the barrel rollers to skid across the raceways, producing smearing, cage wear, and rapid vibration failure. Spring preload devices maintain minimum contact traction during light-load operation.

How do 29326 and 29426 differ on the same 130 mm shaft bore?

Both share d = 130 mm, but 29426 steps up to 270 mm OD, 85 mm overall height H, and 28.3 kg mass versus 225 mm OD, 58 mm H, and 8.48 kg on 29326—giving 29426 substantially higher axial thrust reserve at a lower 850/1,200 rpm ceiling.

Confirming Cage Execution & Oil-Bath Housing Specs for 29000 Thrust Units?

Send your axial load Fa, radial load Fr, shaft orientation, and operating speed. ZQM engineers verify 292/293/294 catalog load ratings, cage execution, and housing abutment drawings before order release.

Request Thrust Bearing Engineering Review

Scroll to Top