While single-row cylindrical roller bearings look deceptively similar from the outside, confusing flange geometry (NU, NJ, and NUP) or ignoring radial internal clearance selection after press-fitting triggers severe axial binding or cage seizure in heavy gearboxes and industrial motors.
Specifically, engineers must distinguish floating NU configurations—which allow free bidirectional axial shaft expansion relative to the housing—from NJ bearings with one integral inner-ring flange that deliver axial location in one direction only, versus NUP locating configurations fitted with an additional loose flange ring.

Separable Rib Architecture: NU vs NJ vs NUP vs Reinforced EM
Selecting the correct cylindrical roller configuration starts with mapping shaft thermal expansion and thrust loads across the locating and non-locating ends of a machine assembly:
NU Series — Pure Bidirectional Floating End
- Two integral outer-ring ribs + ribless inner ring
- Accommodates thermal shaft expansion within the permissible axial displacement limits in both directions
- Separable inner ring eases press-fitting onto tight shaft journals
- Catalog benchmark: NU2326EM (130×280×93 mm, Cr 920 / C0r 1,230 kN)
NJ Series — One-Direction Axial Location
- Two outer-ring ribs + one integral inner-ring retaining rib
- Carries radial load plus axial location in one direction only
- Ideal paired back-to-back or opposing another NJ unit on short shafts
- ZQM Stock model: NJ326EM (130×280×58 mm, Fw = 167 mm)
NUP Series — Bidirectional Axial Locating End
- Two outer ribs, one integral inner rib + loose flange ring
- Restricts axial shaft movement in both directions at a fixed housing
- Slightly higher assembly mass vs. NU/NJ due to separate loose flange ring
- Catalog benchmark: NUP2326M (130×280×93 mm, 30.5 kg) & NUP328M
EM Reinforced Machined Brass Design
- Larger/longer rollers vs. standard M series raise dynamic Cr significantly
- One-piece machined brass cage piloted precisely on roller set or shoulders
- Higher fatigue resistance under reversing torque and shock gear loads
- Legacy EH prefixes (e.g., 42326EH -> NJ326EM) denote reinforced geometry
Verified ZQM Catalog Benchmarks: NJ, NU, and NUP Dimension & Fw Table
Notice the critical importance of Fw (roller under-roller / inner envelope diameter) and abutment limits (Da max). When interchanging separable inner rings across batches or verifying shaft seal interference, always validate Fw alongside nominal d × D × B dimensions:
| ZQM Designation | Legacy Code | Dimensions d×D×B (mm) | Fw (mm) | Cr / C0r (kN) | Grease / Oil Speed (rpm) | Mass (kg) | Locating / Rib Role |
|---|---|---|---|---|---|---|---|
| NU220M | 32220 | 100 × 180 × 34 | 120 | 190 / 260 | 3,200 / 3,800 | 5.20 | Floating NU; brass M cage; Da max 169 mm |
| NU320EM | 32320EH | 100 × 215 × 47 | 127.5 | 380 / 470 | 2,400 / 3,000 | 8.35 | Floating reinforced EM; Da max 202 mm |
| NJ2320M | 42620 | 100 × 215 × 73 | 129.5 | 440 / 630 | 2,400 / 3,000 | 13.5 | One-direction axial location; Da max 197 mm |
| NJ2226EM | 42526 | 130 × 230 × 64 | 153.5 | 530 / 735 | 2,200 / 2,800 | 12.9 | One-direction location; EM reinforced brass |
| NU326EM | 32326EH | 130 × 280 × 58 | 167 | 615 / 735 | 1,800 / 2,200 | 19.3 | Floating NU companion to NJ326EM; Da 258 mm |
| NJ326EM | 42326EH | 130 × 280 × 58 | 167 | 615 / 735 | 1,800 / 2,200 | 19.5 | One-direction locating; db min 149 / Da 258 mm |
| NU2326EM | 32626EH | 130 × 280 × 93 | 167 | 920 / 1,230 | 1,800 / 2,200 | 28.7 | Extra-wide heavy floating NU; Da 258 mm |
| NUP2326M | 92626 | 130 × 280 × 93 | 167 | 920 / 1,230 | 1,800 / 2,200 | 30.5 | Bidirectional locating NUP w/ loose flange ring |
| NU328EM | 32328EH | 140 × 300 × 62 | 180 | 665 / 880 | 1,800 / 2,200 | 23.7 | Floating NU heavy EM; Da max 278 mm |
| NUP328M | 92328 | 140 × 300 × 62 | 180 | 610 / 805 | 1,800 / 2,200 | 24.5 | Bidirectional locating; verify vs. EM capacity |

Radial Clearance Selection: Normal (C0) vs C3 vs C4 After Press Fitting
Because cylindrical roller bearings rely primarily on cylindrical press fits (such as ISO k5, m5, or m6 shaft tolerances on high-torque gearboxes), inner-ring radial expansion during mounting typically consumes 50% to 75% of the effective shaft interference. Combined with higher inner-ring running temperatures vs. water- or air-cooled housings, an insufficiently cleared C0 bearing can drop to zero or negative operating clearance—causing skidding, roller end scoring against ribs, and rapid thermal runaway.
- When to Choose Normal (C0) Clearance: Light-to-moderate shaft interference (j5/k5), minimal temperature differential (< 10 °C between inner and outer rings), and applications requiring tight shaft radial stiffness such as precision machine-tool drives.
- When to Specify C3 Clearance: Standard choice for heavy-duty induction motors, quarry gearboxes, and induction-heated shaft interference fits (m6/n6) where operating inner-ring temperatures run 15–30 °C warmer than the cast-iron housing.
- Why Mixing Unmatched Separable Rings Causes Risks: Even when nominal Fw (e.g., 167 mm on both NU326EM and NJ326EM) matches on paper, standard cylindrical bearings outside specifically marked interchangeable clearance groups must keep factory-paired inner and outer rings together unless explicitly supplied as fully interchangeable sets.

4-Point Specification Checklist for Cylindrical Roller Orders
- Specify Exact Rib Type (NU vs. NJ vs. NUP): Confirm whether the position is bidirectional floating (NU), locating in one direction only (NJ), or fixed in both directions (NUP).
- Confirm Cage Material & Geometry Prefix: Indicate EM (reinforced machined brass) vs. M (standard machined brass) or pressed steel/polyamide alternatives based on peak temperature and shock load.
- Declare Fit Tolerances & Target Clearance: Provide shaft/housing fit grades (e.g., m6 shaft / H7 housing) so factory engineers confirm C0 vs. C3 radial clearance.
- Note Non-Interchangeability Constraints: State whether outer assemblies and inner rings must ship as serialized matched sets or full-lot interchangeable assemblies, and verify legacy codes (e.g., 42326EH -> NJ326EM).
Sourcing NJ, NU, or NUP Cylindrical Roller Bearings?
Share your designation, clearance group (C0/C3/C4), and shaft tolerance details with ZQM’s technical desk to receive factory datasheets and matched-batch availability.

