,

29420 Spherical Roller Thrust Bearing 100 × 210 × 67 mm

Heavy-duty ISO 294-series 29420 spherical roller thrust bearing (100 × 210 × 67 mm) delivering 840 kN dynamic and 2,400 kN static axial ratings for coal pulverizers and severe mixer gearboxes.

Request a Quote

When raw coal laced with iron pyrite or hard shale surges beneath a vertical pulverizer grinding arm—or when dense rubber batches stall a planetary mixer gearbox—lightweight thrust bearings brinell rapidly. Sharing the same 100 mm bore as the 29320 yet expanding to 210 mm OD × 67 mm height and 10.5 kg mass, the ZQM 29420 spherical roller thrust bearing more than doubles dynamic axial capacity to 840 kN (Ca) and raises static shock defense to 2,400 kN (C0a), operating up to 1,600 rpm in oil (1,100 rpm grease).

29420 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 29420
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)100 mm
Boundary Dimensions & WeightOutside diameter (D)210 mm
Boundary Dimensions & WeightOverall height (H)67 mm
Boundary Dimensions & WeightInner-ring width (B)43 mm
Boundary Dimensions & WeightOuter-ring width (C)33 mm
Boundary Dimensions & WeightInner-ring rib / raceway diameter (d1)185 mm
Boundary Dimensions & WeightOuter-ring rib / raceway diameter (D1)144 mm
Boundary Dimensions & WeightReference mass (Weight)10.5 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Ca)840 kN
Load Ratings & Limiting SpeedsBasic static load rating (Coa)2400 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)1100 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)1600 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)150 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)175 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)3 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)2.5 mm
Abutment & Fillet DimensionsAxial offset (S)62 mm

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Why 29420 Outperforms Medium-Series Units Under Mineral Shock

Upgrading a 100 mm shaft from the 293 series to the heavy 29420 transforms shock survivability without re-machining the shaft journal diameter:

  • 2× Capacity Leap on a 100 mm Journal: Deeper 210 mm outer envelopes accommodate substantially larger rollers, jumping Ca from 410 kN (29320) to 840 kN and boosting C0a to 2,400 kN for tramp-iron impact immunity.
  • Thick-Wall Washer Rigidity: A 43 mm shaft washer section (B) paired with a 33 mm housing washer (C) resists elastic dishing when hydraulic tension cylinders clamp grinding rollers onto erratic fuel beds.
  • Misalignment Pivot at S = 62 mm: Casting flex inside tall coal-mill pedestals and mixer housings is absorbed continuously along the spherical housing raceway centered 62 mm from the shaft washer face.
  • Radial-Axial Boundary Control: Steep roller contact geometry sustains combined radial overturning moments up to Fr ≤ 0.55 · Fa while locking the vertical output spindle cleanly.

Dimensional Reference Matrix for 29420 Across Major Makers

Manufacturer Model Reference d (mm) D (mm) H (mm) Series Characteristics
ZQM 29420 100 210 67 ISO 294 heavy series; cage spec confirmed upon inquiry
SKF 29420 E 100 210 67 Stamped steel cage high-capacity design
FAG / Schaeffler 29420-E1 100 210 67 Reinforced roller profile without center guide lip
NSK 29420 / 29420M 100 210 67 Available in machined brass cage configuration
Timken / NTN 29420EM / 29420 100 210 67 Heavy axial shock industrial variants

Interchange caveat: Every designation above conforms to the ISO 104 nominal boundary of 100 × 210 × 67 mm strictly for preliminary identification. Internal roller crowning, guide-flange design, and cage metallurgy differ by producer; verify axial clearance and oil-passage alignment on your pulverizer assembly drawing prior to substitution.

Pulverizer & Mixer Gearbox Service Protocol for 29420

  • Heavy-Duty Shoulder Backing: Because the 29420 transmits up to 2,400 kN static spikes, machine rigid shaft shoulders to da ≥ 150 mm (washer OD d1 = 185 mm) and housing shoulders to Da ≤ 175 mm (washer bore D1 = 144 mm), keeping transition fillets to ra ≤ 2.5 mm inside the 3 mm minimum ring chamfer.
  • Oil Sump Filtration & Abrasive Control: Fine pulverized coal dust acts like lapping paste once it breaches shaft seals. Run circulating ISO VG 220–320 EP gear oil through fine duplex filters and install magnetic drain plugs beneath the 29420 seat to flag early spalling debris.
  • Minimum Axial Preload During Idle Rotation: When grinding arms lift off the bull ring during mill warm-up, maintain minimum spring-applied axial thrust so the heavy 10.5 kg roller set stays in pure rolling contact instead of skidding across the raceway.
  • Heat-Assisted Fitting: Warm the shaft washer inductively to 90–110 °C before sliding it onto the 100 mm interference journal, then re-seat firmly once cooled so zero axial gap remains against the shoulder.

Planning a power-plant mill overhaul or heavy mixer gearbox upgrade? Share your operating rpm, peak shock load, and oil viscosity with our industrial bearing specialists for verified cage and tolerance recommendations.

Coal Mill & Heavy Mixer 29420 Technical FAQ

Related Selection & Comparison: When housing axial height is restricted on a 100 mm shaft, evaluate the more compact 29320 thrust bearing, review heavy pulverizer station layouts in our Mining & Crushing Hub, or check all sizes under Thrust Roller Bearings.

When should an engineer step up from 29320 to 29420 on a 100 mm shaft?

Choose 29420 whenever intermittent impact loads, high hydraulic clamping pressures, or severe vibration threaten fatigue life. Although bore stays 100 mm, the 29420 increases dynamic load rating by 105% (840 kN vs 410 kN) and nearly doubles static capacity to 2,400 kN.

Is grease lubrication acceptable for a 29420 inside a coal pulverizer reducer?

Grease is only viable on very slow intermittent shafts well below 1,100 rpm. Continuous pulverizer and mixer gearboxes require oil-bath or forced circulating oil (rated up to 1,600 rpm) to flush wear particles and dissipate heat from the wide roller-flange sliding contacts.

Why does the 29420 require a 3 mm chamfer and ra ≤ 2.5 mm shaft fillet?

Large 100 mm mixer shafts carry high torsional torque alongside axial thrust, demanding generous fillets to avoid shaft fatigue cracks. Keeping ra at or below 2.5 mm ensures the 43 mm shaft washer seats flush without riding up onto the fillet radius.

Can a single 29420 handle upward bounce when hard tramp metal passes under a grinding roller?

No—a single spherical roller thrust bearing carries axial force in one direction only. Pair it with an opposing hold-down bearing or hydraulic rebound stop to restrain reverse lift while keeping minimum axial load engaged on the primary 29420.

Scroll to Top