Inside a co-rotating twin-screw plastic or rubber compounding extruder, die-head back-pressure pushes continuously rearward along twin parallel shafts separated by tight center distances. The ZQM 29320 spherical roller thrust bearing packs 410 kN basic dynamic axial capacity (Ca) and 1,280 kN static axial capacity (C0a) into a compact 100 × 170 × 42 mm envelope weighing 3.91 kg, reaching 2,000 rpm under oil lubrication (1,500 rpm grease) without forcing designers to widen the gearbox casing.
29320 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 100 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 170 mm |
| Boundary Dimensions & Weight | Overall height (H) | 42 mm |
| Boundary Dimensions & Weight | Inner-ring width (B) | 26.2 mm |
| Boundary Dimensions & Weight | Outer-ring width (C) | 20.8 mm |
| Boundary Dimensions & Weight | Inner-ring rib / raceway diameter (d1) | 152 mm |
| Boundary Dimensions & Weight | Outer-ring rib / raceway diameter (D1) | 128 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 3.91 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Ca) | 410 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Coa) | 1280 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1500 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 2000 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 130 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 150 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 1.5 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 1.5 mm |
| Abutment & Fillet Dimensions | Axial offset (S) | 58 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
How the 29320 Handles Continuous Extruder Back-Pressure
Polymer melt viscosity fluctuates every time resin grades change or screen changers clog, imposing steady axial push combined with slight gear-mesh radial force on the output pinions. The 29320 addresses these extruder gearbox realities through asymmetric barrel-roller geometry:
- Slim 42 mm Axial Stack Height: With shaft washer thickness B = 26.2 mm and housing washer height C = 20.8 mm, multiple 29320 units or tandem thrust assemblies fit cleanly behind helical reduction stages where axial shaft space is strictly budgeted.
- Self-Alignment Around Sphere Center S = 58 mm: Barrel-shaped rollers run against a concave spherical housing washer raceway centered 58 mm from the shaft washer back face, absorbing thermal casing bow from adjacent 200 °C heated extruder barrels.
- Combined Radial Load Margin: While primarily an axial component, the steep contact angle tolerates radial gear-separating reactions up to Fr ≤ 0.55 · Fa when paired properly with radial pilot bearings.
- High Oil-Cooled Speed Ceiling: At 2,000 rpm oil limit, the 29320 accommodates high-throughput compounding screws that run far faster than legacy single-screw lines.
ISO 104 Nominal Envelope Cross-Reference for 29320
| Brand | Reference Code | Bore d (mm) | OD D (mm) | Height H (mm) | Engineering Notes |
|---|---|---|---|---|---|
| ZQM | 29320 | 100 | 170 | 42 | Catalog baseline; cage & clearance confirmed per order |
| SKF | 29320 E | 100 | 170 | 42 | Stamped steel cage Explorer geometry |
| FAG / Schaeffler | 29320-E1 | 100 | 170 | 42 | X-life internal roller profile |
| NSK / NTN | 29320 / 29320M | 100 | 170 | 42 | Machined brass or steel cage variants |
| Timken | 29320EM | 100 | 170 | 42 | Machined brass cage execution |
Boundary notice: Listed manufacturer codes share identical ISO 104 nominal dimensions (100 × 170 × 42 mm) for dimensional lookup only. Cage material, roller count, internal clearance, and oil-flow porting vary across brands, so direct interchange must always be checked against the extruder gearbox blueprint.
Extruder Thrust Block Mounting & Oil-Cooling Playbook
- Respect Shoulder Geometry: Machine the shaft abutment to da ≥ 130 mm (matching shaft washer OD d1 = 152 mm) and hold the housing seat bore abutment to Da ≤ 150 mm (housing washer bore D1 = 128 mm). Keep corner fillets at ra ≤ 1.5 mm to clear the 1.5 mm minimum ring chamfer.
- Prioritize Circulating Oil Over Grease: Extruder thrust chambers absorb conducted heat from the feed throat. Feed filtered ISO VG 150–220 gear oil into the bore side so centrifugal roller pumping sweeps cool oil radially outward toward a cooled sump return; use grease only on slow rubber extruders well below 1,500 rpm.
- Guard Against Unloaded Screw Skidding: Whenever operators run dry barrel-purge cycles with zero die pressure, maintain minimum axial spring preload on the 29320 so centrifugal forces do not cause roller skidding and raceway smearing.
- Leave Radial Freedom on the Housing Washer: Fit the shaft washer tightly (typically k6/m6) so it never creeps, while leaving slight radial clearance around the 170 mm housing washer outer diameter when pure axial duty applies so self-alignment remains unobstructed.
Need cage-option confirmation (pressed steel vs machined brass) or a dimensional check for your twin-screw gearbox rebuild? Submit shaft speed, melt back-pressure, and oil grade via our engineering quotation desk, or review bearing selection calculators in our technical tools hub.
Extruder Engineering Q&A for the 29320 Bearing
Related Selection & Comparison: For higher impact shock loads on the same 100 mm shaft, compare the heavier 29420 thrust roller bearing (210 × 67 mm), explore the full Thrust Roller Bearings catalog, or verify axial fatigue life in our ISO 281 Bearing Life Calculator.
Why does a twin-screw extruder thrust box choose 29320 instead of a tandem thrust ball bearing?
Thrust ball bearings tolerate almost zero angular tilt and suffer rapid edge stress when heated extruder gearboxes deform thermally. The 29320 accommodates housing misalignment naturally around its 58 mm spherical center while delivering 410 kN dynamic axial load capacity in just 42 mm of height.
Can the 29320 run continuously at 1,800 rpm in a compounding line?
Yes, provided circulating oil lubrication with external cooling is active. Its catalog oil speed rating reaches 2,000 rpm, whereas grease lubrication caps at 1,500 rpm because trapped grease cannot shed frictional heat fast enough in continuous extrusion duty.
What happens if radial gear-tooth force exceeds 55% of axial die pressure?
If radial load climbs above Fr = 0.55 · Fa, rollers unload on one half of the raceway, skewing the cage and raising oil temperature abruptly. Separate radial cylindrical roller bearings must carry the pinion gear separating forces while the 29320 focuses on axial thrust.
How should maintenance teams verify abutment wear before installing a replacement 29320?
Inspect shaft shoulder flatness and verify da stays at least 130 mm with fillet radius ≤ 1.5 mm. Any burr or concave wear step under the shaft washer back face concentrates bending stress across the 26.2 mm washer and triggers premature cracking.



