Every few minutes inside a sugar refinery or fine-chemical dewatering plant, a massive vertical perforated basket packed with wet crystals accelerates from rest to 1,200 rpm, drains mother liquor, and brakes sharply for plow discharge. Suspended on a 140 mm main spindle, the ZQM 29328 spherical roller thrust bearing (140 × 240 × 60 mm, 10.4 kg) carries high-inertia basket weight plus scraper-knife downforce with 840 kN dynamic capacity (Ca), 2,810 kN static capacity (C0a), and 1,400 rpm oil-lubricated speed capability (950 rpm grease).
29328 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 140 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 240 mm |
| Boundary Dimensions & Weight | Overall height (H) | 60 mm |
| Boundary Dimensions & Weight | Inner-ring width (B) | 38.5 mm |
| Boundary Dimensions & Weight | Outer-ring width (C) | 30 mm |
| Boundary Dimensions & Weight | Inner-ring rib / raceway diameter (d1) | 216.5 mm |
| Boundary Dimensions & Weight | Outer-ring rib / raceway diameter (D1) | 179 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 10.4 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Ca) | 840 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Coa) | 2810 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 950 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1400 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 185 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 205 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 2.1 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2 mm |
| Abutment & Fillet Dimensions | Axial offset (S) | 82 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Managing Cyclic Inertia & Cake Unbalance with the 29328
Batch basket centrifuges punish thrust bearings with rapid thermal cycling, eccentric filter-cake vibration, and brief low-load wash steps:
- High-Speed Large-Bore Capability: Reaching 1,400 rpm under circulating oil on a 140 mm shaft allows direct-drive VFD centrifuge spindles to spin full batches without overheating the 60 mm tall roller complement (shaft ring B = 38.5 mm, housing ring C = 30 mm).
- Rubber-Buffer Suspension Articulation: Vertical centrifuges sway intentionally on elastomeric isolation mounts when sugar or salt crystals distribute unevenly; the 29328 pivots effortlessly around sphere center S = 82 mm so spindle sway does not edge-load the raceways.
- Controlled Radial Eccentricity Margin: Heavy eccentric unbalance spikes must be absorbed primarily by upper radial cylindrical/spherical roller bearings so lateral load on the 29328 stays strictly within Fr ≤ 0.55 · Fa.
- 2,810 kN Scraper-Plow Impact Buffer: When hardened crystalline cake resists the hydraulic discharge knife, axial reaction surges abruptly—well inside the 29328’s static threshold.
ISO 104 Nominal Dimension Cross-Reference for 29328
| Brand | Model Code | Bore d | OD D | Height H | Process Equipment Notes |
|---|---|---|---|---|---|
| ZQM | 29328 | 140 mm | 240 mm | 60 mm | Factory catalog baseline; cage confirmed per quote |
| SKF | 29328 E | 140 mm | 240 mm | 60 mm | Stamped steel cage Explorer series |
| FAG / Schaeffler | 29328-E1 | 140 mm | 240 mm | 60 mm | High-speed modified roller geometry |
| NSK / NTN | 29328 / 29328M | 140 mm | 240 mm | 60 mm | Machined brass or steel cage executions |
| Timken | 29328EM | 140 mm | 240 mm | 60 mm | Heavy machined brass cage option |
Engineering disclaimer: Cross-referenced designations correspond solely on ISO 104 nominal boundary envelope (140 × 240 × 60 mm). Cage dynamics during fast cyclic spin-up and oil-churning losses differ across manufacturers; verify centrifuge head tolerances and lubrication delivery before authorizing a brand switch.
Centrifuge Spindle Lubrication & Minimum-Load Playbook
- Exact Spindle Seat Dimensions: Machine the spindle shoulder to da ≥ 185 mm (supporting d1 = 216.5 mm shaft washer OD) and housing seat shoulder to Da ≤ 205 mm (D1 = 179 mm), capping corner fillets at ra ≤ 2 mm for the 2.1 mm minimum ring chamfer.
- Switch to Circulating or Air-Oil Feed Above 900 rpm: Heavy grease churns violently at 1,100–1,350 rpm batch speeds, exceeding the 950 rpm grease limit and baking within days. Feed clean ISO VG 68–100 oil continuously from the bore side with an unrestricted lower drain so oil cannot flood the housing.
- Enforce Minimum Axial Load During Empty Wash Cycles: When an empty basket accelerates during CIP rinse, reduced axial weight lets centrifugal forces tilt rollers and trigger raceway smearing. Verify that dead spindle-plus-basket mass—or supplementary axial preload springs—exceeds the minimum load requirement across the entire speed curve.
- Isolate Corrosive Process Vapors: Acidic chemical mist or hot sugar-syrup steam rapidly pits bearing steel; protect the 29328 cartridge with nitrogen-purged or dry-air labyrinth barriers beneath the basket hub.
Rebuilding a sugar-centrifuge spindle head or specifying spares for chemical batch dryers? Share batch cycle rpm, basket dead weight, and vapor sealing setup via our ZQM engineering contact page for matched bearing recommendations.
Vertical Basket Centrifuge 29328 Technical FAQ
Related Selection & Comparison: Need even higher static capacity for vertical mill tables? Compare the 150 mm 29430 or flagship 420 mm 29384 thrust bearing, and test Fr ≤ 0.55·Fa limits in our ISO 281 Life Calculator.
Why do centrifuge thrust bearings smear during empty-basket spin tests?
Spherical roller thrust bearings require a minimum axial load to overcome centrifugal roller forces at high rpm. If an unloaded spindle spins near 1,200–1,400 rpm without sufficient basket dead weight or spring preload, rollers skid instead of rolling cleanly.
Can the 29328 handle severe radial vibration from uneven sugar cake loading?
Only up to Fr ≤ 0.55 · Fa. Centrifuge heads must pair the 29328 with dedicated upper and lower radial bearings to absorb eccentric cake unbalance while letting the 29328 carry vertical gravity and plow forces.
What oil viscosity works best for a 29328 spinning at 1,250 rpm?
At 1,250 rpm (close to the 1,400 rpm oil rating), ISO VG 68 or VG 100 circulating mineral or synthetic oil provides strong film thickness without the excessive viscous drag and temperature spike caused by heavier VG 320 gear oils.
Why should the housing washer outer diameter (240 mm) have radial clearance in a centrifuge head?
When radial bearings manage lateral unbalance, giving the 240 mm housing washer slight radial clearance prevents radial housing forces from locking the washer and preserves smooth self-alignment around S = 82 mm.





