Suspended beneath the discharge head of a deep-well vertical turbine pump or coastal circulating water pump, dozens of meters of line shaft plus multi-stage impeller hydraulic suction pull relentlessly downward 24 hours a day. The ZQM 29322 spherical roller thrust bearing (110 × 190 × 48 mm, 6.94 kg) absorbs this continuous hydraulic downthrust with 530 kN dynamic capacity (Ca), 1,710 kN static capacity (C0a), and an oil-lubricated speed ceiling of 1,800 rpm (1,300 rpm grease) that fits standard 4-pole 50/60 Hz vertical motor drives cleanly.
29322 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 110 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 190 mm |
| Boundary Dimensions & Weight | Overall height (H) | 48 mm |
| Boundary Dimensions & Weight | Inner-ring width (B) | 16 mm |
| Boundary Dimensions & Weight | Outer-ring width (C) | 23 mm |
| Boundary Dimensions & Weight | Inner-ring rib / raceway diameter (d1) | 175 mm |
| Boundary Dimensions & Weight | Outer-ring rib / raceway diameter (D1) | 143 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 6.94 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Ca) | 530 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Coa) | 1710 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1300 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1800 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 145 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 165 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 2 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2 mm |
| Abutment & Fillet Dimensions | Axial offset (S) | 64 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Hydraulic Downthrust Mechanics in 29322 Pump Thrust Pots
Cooling-water intake pumps and desalination feed pumps run uninterrupted for entire seasons, making thermal equilibrium and self-pumping oil flow decisive design factors:
- 4-Pole Speed Alignment (1,480–1,780 rpm): Rated to 1,800 rpm under oil bath cooling, the 29322 runs smoothly beneath direct-coupled 50 Hz and 60 Hz hollow-shaft vertical motors without dropping into speed-derating territory.
- Built-In Centrifugal Oil Circulation: As the 110 mm shaft washer rotates inside a submerged thrust pot, the tilted asymmetric rollers act like a mini impeller—drawing cool turbine oil upward through the bore gap (D1 = 143 mm) and flinging warmed oil outward across cooling coils.
- Column-Flange Alignment Forgiveness: Long vertical pump columns rarely sit dead plumb; the concave spherical housing raceway pivots around offset S = 64 mm so foundation settling never pinches one side of the roller complement.
- Combined Radial Whip Tolerance: Minor impeller imbalance and shaft runout are safely held as long as radial force stays within Fr ≤ 0.55 · Fa alongside upper/lower radial guide bushings.
Cross-Brand ISO 104 Lookup Table for 29322
| Maker | Part Number | Bore d | OD D | Height H | Typical Pump Application Note |
|---|---|---|---|---|---|
| ZQM | 29322 | 110 mm | 190 mm | 48 mm | Factory catalog geometry; cage confirmed per quote |
| SKF | 29322 E | 110 mm | 190 mm | 48 mm | Pressed steel window cage variant |
| FAG / Schaeffler | 29322-E1 | 110 mm | 190 mm | 48 mm | High-capacity asymmetrical roller design |
| NSK / NTN | 29322 / 29322M | 110 mm | 190 mm | 48 mm | Machined brass or steel cage options |
| Timken | 29322EM | 110 mm | 190 mm | 48 mm | One-piece machined brass cage |
Specification reminder: Equivalence in the chart above covers ISO 104 nominal envelope dimensions (110 × 190 × 48 mm) exclusively. Because oil-slinger clearances, cage guidance, and thermal speed behavior differ among suppliers, confirm thrust-pot oil depth and mating carrier dimensions against pump OEM documentation before swapping brands.
Vertical Thrust Pot Oil-Bath & Installation Checklist
- Verify Thrust Carrier Shoulders: Machine the rotating shaft sleeve shoulder to da ≥ 145 mm (supporting d1 = 175 mm washer OD) and keep the stationary housing seat lip at Da ≤ 165 mm, maintaining fillet radius ra ≤ 2 mm to clear the 2 mm minimum bearing chamfer.
- Submerge Properly with Cooling Coils: Fill the thrust reservoir with rust-and-oxidation-inhibited ISO VG 46 or VG 68 turbine oil so static oil level sits near the roller pitch center; route raw cooling water through copper finned coils inside the pot when continuous pump speed exceeds 1,450 rpm.
- Control Start-Up Upthrust Transients: During initial pump start against a closed discharge valve, momentary hydraulic upthrust can lift the rotor. Install a matched hold-down ball bearing or preloaded spring ring so the 29322 never loses its minimum axial load and skids.
- Monitor Sight Glass & RTD Probe: Mount a spring-loaded platinum RTD directly beneath the stationary housing washer (190 mm OD) to catch oil foaming, water-coil leaks, or emulsified lubricant long before raceway seizure occurs.
Specifying replacement bearings for a municipal waterworks, refinery cooling tower, or deep-well turbine pump? Send pump head, rpm, and thrust-pot cooling layout to our application engineering team for prompt quotation and stock verification.
Vertical Turbine Pump 29322 FAQ
Related Selection & Comparison: For heavier 120 mm vertical shaft thrusts, step up to the 29424 heavy thrust roller bearing, review our CMM & NDT Quality Control Lab standards, or browse all Thrust Roller Bearings.
Why do 1,750 rpm vertical water pumps require oil-bath cooling instead of grease for the 29322?
At 1,750 rpm, the 29322 operates above its 1,300 rpm grease ceiling and right near its 1,800 rpm oil rating. Continuous oil-bath circulation with submerged water coils is mandatory to carry away roller-rib sliding heat and stabilize sump temperature below 75 °C.
What happens if the thrust-pot oil level is overfilled above the recommended mark?
Excessive oil depth causes heavy viscous churning at 1,450–1,750 rpm, whipping air bubbles into the lubricant, spiking bearing temperature by 15–20 °C, and forcing oil mist up through the top standpipe labyrinth.
How does the 29322 tolerate slight misalignment between the motor stool and wellhead baseplate?
Its spherical housing washer raceway pivots around a sphere center 64 mm from the shaft washer back face, permitting smooth angular self-adjustment without generating edge stress along the rollers.
What is the maximum allowable radial load on the 29322 inside a pump thrust pot?
Keep radial load at or below 55% of concurrent axial downthrust (Fr ≤ 0.55 · Fa). Larger lateral impeller loads must be taken by the pump’s lower line-shaft guide bearings rather than the top thrust pot.




