,

29332 Spherical Roller Thrust Bearing 160 × 270 × 67 mm

ISO 104 29332 spherical roller thrust bearing (160 × 270 × 67 mm, 14.3 kg) delivering 1,010 kN dynamic and 3,400 kN static axial ratings with 1,200 rpm oil speed for vertical coal-pulverizer bowl mill main thrust pedestals.

Request a Quote

Directly underneath the spinning grinding table of a power-station vertical coal-pulverizer bowl mill, pneumatic-hydraulic spring cylinders press three heavy journal rolls onto raw coal beds while hot primary drying air blasts upward around the bowl skirt. Carrying that relentless downward crushing force across a 160 × 270 × 67 mm ISO 104 envelope (shaft washer height B = 42 mm, housing washer height C = 33 mm, weight 14.3 kg), the ZQM 29332 spherical roller thrust bearing provides 1,010 kN dynamic axial capacity (Ca), 3,400 kN static crush margin (C0a), and limiting speeds of 850 rpm grease or 1,200 rpm oil.

29332 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 29332
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)160 mm
Boundary Dimensions & WeightOutside diameter (D)270 mm
Boundary Dimensions & WeightOverall height (H)67 mm
Boundary Dimensions & WeightInner-ring width (B)42 mm
Boundary Dimensions & WeightOuter-ring width (C)33 mm
Boundary Dimensions & WeightInner-ring rib / raceway diameter (d1)243 mm
Boundary Dimensions & WeightOuter-ring rib / raceway diameter (D1)203 mm
Boundary Dimensions & WeightReference mass (Weight)14.3 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Ca)1010 kN
Load Ratings & Limiting SpeedsBasic static load rating (Coa)3400 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)850 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)1200 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)210 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)235 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)3 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)2.5 mm
Abutment & Fillet DimensionsAxial offset (S)92 mm

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Self-Aligning Bowl-Mill Mechanics Inside the 29332 Pedestal

Thermal gradients between a 260 °C primary-air mill body and the cooler lower worm/bevel gearbox inevitably tilt the main vertical pedestal flange. The 29332 neutralizes these mill-floor disturbances through four structural traits:

  • Up to ~2° Dynamic Self-Alignment: Asymmetric barrel rollers track smoothly along the concave spherical housing washer raceway, accommodating thermal bowl tilt and uneven coal-bed loading without pinching roller corners.
  • 3,400 kN Static Tramp-Iron Cushion: When mine roof-bolts or dense pyrite chunks lodge momentarily beneath a grinding roll, the 3,400 kN static rating guards raceways against permanent brinell craters.
  • Combined Radial-Axial Envelope (Fr ≤ 0.55 Fa): Asymmetric coal-bed thickness induces horizontal shaft deflection alongside vertical grinding thrust; the steep contact geometry safely absorbs radial components up to 55% of concurrent axial load.
  • Built-In Oil-Bath Pumping Circulation: Tilted roller geometry continuously draws cooler gear oil inward and flings heated lubricant radially outward toward pedestal wall heat sinks—vital inside enclosed mill pedestals operating near the 1,200 rpm oil envelope.

ISO 104 Bowl-Mill Cross-Reference Matrix for 29332

Brand Reference Number Bore d OD D Height H Pulverizer Duty Remarks
ZQM 29332 160 mm 270 mm 67 mm Catalog ISO 104 medium thrust; cage verified per order
SKF 29332 E 160 mm 270 mm 67 mm Pressed steel window cage high-capacity profile
FAG / Schaeffler 29332-E1 160 mm 270 mm 67 mm Reinforced asymmetric roller internal design
NSK / NTN 29332 / 29332M 160 mm 270 mm 67 mm Machined brass or steel cage industrial executions
Timken 29332EM 160 mm 270 mm 67 mm Solid machined brass cage thrust assembly

Dimensional equivalence notice: Listed part numbers match strictly on ISO 104 nominal external boundaries (160 × 270 × 67 mm) for cross-lookup purposes and do not guarantee identical cage metallurgy, roller count, or oil-passage geometry. Always verify cage construction and pedestal oil-dam clearance against the pulverizer OEM bill of materials before substitution.

Pedestal Shoulder Geometry & Mill Overhaul Installation Steps

  1. Respect Heavy Abutment & Chamfer Clearances: Turn the vertical main-shaft support shoulder to da = 210 mm (minimum) and hold the lower pedestal housing seat abutment at Da = 235 mm (maximum), keeping transition fillets safely below the rmin = 3.0 mm bearing chamfer so the 42 mm shaft washer and 33 mm housing washer seat flat without bending.
  2. Separate Dimensional Fit from Seat Flatness: Machine the 160 mm straight cylindrical vertical journal to ISO 286-1 IT6 interference (commonly k6/m6) so the shaft washer cannot fret under torque, while separately verifying ISO 1101 shoulder perpendicularity and housing-seat flatness across the full 270 mm pocket.
  3. Allow Slight Radial Freedom on the Housing Washer OD: Under pure or predominantly vertical axial grinding loads, leave a light radial gap around the stationary 270 mm housing washer so its spherical raceway self-aligns freely as the mill pedestal warms up.
  4. Inductive Warm-Mounting for the 14.3 kg Assembly: Heat the shaft washer cleanly to 95–110 °C on an induction coil, lower it straight onto the 160 mm journal, and re-verify zero shoulder gap once cooled to ambient shop temperature.

Oil-Bath Heat Rejection & Coal-Dust Exclusion Protocol

Pulverizer pedestals suffer from two silent killers: conducted heat from hot primary drying air and ultra-fine abrasive coal dust sneaking past worn seal-air labyrinths. Maintain positive seal-air pressure above mill differential pressure at all times, fill the thrust pedestal with oxidation-inhibited ISO VG 220–320 EP gear oil to the OEM sight-glass mark, and route oil through an external finned cooler whenever sump temperatures climb past 70 °C. During unloaded warm-up spins with grinding rolls retracted, verify that rotor deadweight satisfies minimum axial load so rollers do not smear.

Power-Plant Outage Checklist & Quotation Path

Ahead of your boiler-unit scheduled outage, confirm four items for 29332 procurement: (1) cage preference (machined brass vs heavy stamped steel), (2) actual shaft rpm and peak hydraulic roll-loading tonnage, (3) existing pedestal oil viscosity and cooler capacity, and (4) inspection records of the mating 210 mm shaft shoulder for fret grooving. Request stock lead times and inspection documentation via our ZQM power-generation quotation team.

Engineering Calculators & Related Hubs: Estimate bowl-mill fatigue hours in our ISO 281 Bearing Life Calculator, verify exact specs at 29332 Catalog Record, browse all sizes under Thrust Roller Bearings, or explore coal-grinding layouts in Mining & Crushing Applications.

Vertical Coal Bowl Mill 29332 Technical FAQ

How much bowl tilt can the 29332 absorb inside a hot coal pulverizer?

Its concave spherical housing washer permits up to roughly 2° of dynamic angular self-alignment under operating load, neutralizing thermal bowl warpage and uneven coal-bed height without overloading one sector of the rollers.

Why must radial shaft load stay within Fr ≤ 0.55 Fa on the 29332?

Exceeding 55% radial-to-axial load ratio unloads rollers across nearly half the raceway circumference, triggering roller skew, heavy cage-pocket rubbing, and sudden oil-bath overheating. Upper and lower radial guide bearings must carry primary horizontal grinding reactions.

When is grease unacceptable in a 29332 coal-mill pedestal?

Although the catalog lists an 850 rpm grease ceiling, continuous coal pulverizers conduct substantial radiant heat into the thrust sump and require continuous oil-bath or circulating oil cooling (rated up to 1,200 rpm) to flush wear fines and reject frictional heat.

Why should maintenance crews inspect the 210 mm shaft abutment during every 29332 replacement?

Under 1,010 kN dynamic and 3,400 kN static forces, even minor concave wear or fretting steps on the shaft abutment turn the 42 mm shaft washer into a cantilevered beam, initiating radial through-cracks shortly after restart.

Scroll to Top