The 2208 self-aligning ball bearing (40 × 80 × 23 mm, ISO 15 Dimension Series 22) expands axial width by 5 mm over the narrow 1208 while preserving the exact same 40 mm bore and 80 mm housing diameter. That extra cross-sectional volume gives woodworking planer feed-rolls, gang-rip edgers, and timber resaw shafts stiffer radial support against V-belt pull—with optional -2RS contact lip seals to lock fine sawdust out, or 2208K (1:12 tapered bore) for 35 mm plain shafting via an H308 sleeve.
| ISO 15 Field | Symbol | 2208 Value | Series 22 Engineering Notes |
|---|---|---|---|
| Bore Diameter | d | 40 mm | ISO 15 Straight Bore |
| Outside Diameter | D | 80 mm | Matches 1208 housing OD |
| Wide-Series Width | B | 23 mm | 5 mm wider than 1208 (18 mm) |
| Tapered & Sealed Options | 2208K / -2RS | 1:12 Taper / Dual Seals | 2208K fits 35 mm shaft with H308 sleeve |
| Contact Geometry | Double-Row Ball | Sphered Outer Track | Point contact (p = 3); wider ball spacing |
| Load Ratings & Cage | Cr / C0r / Cage | Factory Drawing Verified | Steel or polyamide cage confirmed per quote |
2208 Wide-Series Advantage in Sawmills & Planer Mills
Four-sided moulders, thickness planers, and multi-blade sawmill edgers impose steep radial V-belt tension alongside fluctuating timber-feed resistance whenever dense knots strike the infeed rollers. Fabricated steel mill frames rarely remain dead-true after years of board impacts. By stretching width to 23 mm inside the 40 × 80 mm footprint, the 2208 widens the span between its two ball rows and increases load stamina compared with an 18 mm wide 1208—yet still articulates smoothly to swallow roughly 2°–2.5° of frame deflection.
Because wood chips, resin pitch, and fine sander dust quickly foul open pedestals, timber-processing plants frequently request 2208-2RS pre-lubricated units with dual nitrile contact seals. Note two practical engineering boundaries when choosing sealed variants: contact lip seals restrict maximum permissible misalignment slightly compared with open bearings (typically around 1.5° so the seal lip maintains contact without lifting), and internal grease life dictates service intervals. Cage selection (stamped steel vs polyamide ~120 °C ceiling) and final dynamic/static ratings are confirmed on our formal drawing before shipment.
2208 Equivalent Part Numbers & Legacy Code Mapping
Sawmill maintenance teams servicing European moulders alongside older domestic timber machinery often cross-check these ISO 15 Series 22 numbers (note the legacy Chinese code 1508):
| Brand / Standard | Open Cylindrical | Tapered (1:12) / Sealed Variants | Technical Checkpoints |
|---|---|---|---|
| ZQM Bearings | 2208 | 2208K / 2208-2RS / 2208K-2RS | Factory print verifies seal lip, grease & cage |
| SKF | 2208 ETN9 | 2208 EKTN9 / 2208 E-2RS1TN9 | 2RS1 = nitrile seals; TN9 = polyamide cage |
| FAG / Schaeffler | 2208-TVH | 2208-K-TVH / 2208-2RS-TVH | Confirm clearance & grease fill for dusty mills |
| NSK / NTN | 2208 | 2208K / 2208LLU (2RS) | Verify seal contact drag vs cutterhead speed |
| Legacy GB Code | 1508 | 11508 (tapered) | Old Chinese code for 2208 wide series |
Interchange Scope: Equivalency confirms matching 40 × 80 × 23 mm ISO 15 exterior geometry only. Seal elastomer compound, factory grease type, ball count, and cage limits vary across manufacturers and must be verified against equipment manuals prior to installation.
Woodworking Feed-Roll Sealing & Adapter Sleeve Practice
On timber infeed tables and edger arbor supports across forest-products and woodworking equipment, resinous sap mixes with airborne pine dust to form a sticky paste around rotating seals. Even when fitting 2208-2RS sealed bearings inside split pillow housings, pairing the housing with external felt or labyrinth V-rings shields the primary rubber lips from coarse wood slivers.
When replacing bearings on worn 35 mm edger drive shafts, 2208K paired with an H308 metric adapter sleeve clamps solidly without requiring weld build-up of the original journal. Never try to fit a heavy-shock sawmill main saw arbor requiring high impact resistance with a ball bearing if the machine builder specified a 22208 spherical roller bearing—check radial shock severity carefully.
Ordering 2208, 2208K & 2208-2RS for Timber Machinery
Send our sales engineers your required execution (open 2208, dual-sealed 2208-2RS, or 1:12 tapered 2208K with H308 sleeve), preferred steel or polyamide retainer, internal clearance (CN or C3), and quantity. We issue a verified factory drawing covering boundary dimensions, ratings, and grease fill prior to production.
Get a Quote & Drawing for 2208 Timber Bearings
2208 Practical FAQ for Woodworking & Sawmill Maintenance
Related Selection & Comparison: Compare narrow 18 mm width on the same 40 mm bore via 1208, check H308 1:12 sleeve pairing in our Tapered Bore Tool, or browse all Self-Aligning Ball Bearings.
Can a 2208 replace a 1208 inside the same 80 mm pillow block?
Both share 40 mm bore and 80 mm OD, but 2208 is 23 mm wide versus 1208’s 18 mm width. It fits only if the housing recess and locating-ring spacing accommodate the extra 5 mm axial width.
Does adding -2RS contact seals change the allowable misalignment of a 2208?
Yes. Contact rubber seals must remain seated against the inner ring shoulder to exclude sawdust, which narrows practical misalignment allowance to roughly 1.5° compared with ~2.5° on an open 2208.
Why does 2208K use an H308 adapter sleeve instead of H208?
Because the 2208K is 23 mm wide, it requires the longer H308 sleeve (for a 35 mm shaft) so the tapered seat fully supports the wider inner ring; H208 is sized only for the 18 mm wide 1208K.
What is the old Chinese bearing code for 2208?
Older woodworking machinery drawings from China list 2208 as legacy code 1508 (and tapered 2208K as 11508), sharing identical 40 × 80 × 23 mm ISO 15 boundary dimensions.



