The 1208 self-aligning ball bearing (40 × 80 × 18 mm, ISO 15 Dimension Series 02) pairs two rows of precision balls with a continuous sphered outer-ring raceway so slender air-handling and centrifugal blower shafts can flex without inducing edge stress. Available with a straight 40 mm bore or as 1208K with a 1:12 tapered bore for mounting onto 35 mm commercial shafting via an H208 adapter sleeve, it delivers cool, low-friction running across rooftop air handlers and ducted ventilation units.
| Parameter | Symbol | 1208 Nominal Value | Reference Standard / Notes |
|---|---|---|---|
| Bore Diameter (Cylindrical) | d | 40 mm | ISO 15 Dimension Series 02 |
| Outside Diameter | D | 80 mm | ISO 15 Nominal Boundary |
| Width | B | 18 mm | Narrow Series 12 Envelope |
| Optional Tapered Bore | 1208K | 1:12 Taper | Pairs with H208 Sleeve (35 mm shaft) |
| Rolling Geometry | Double-Row Ball | Sphered Outer Raceway | Point contact (p = 3 life exponent) |
| Load Ratings, Speed & Cage | Cr / C0r / rpm | Confirmed on Factory Drawing | Verified per cage & clearance execution at quotation |
1208 Geometry & Quiet Running in Centrifugal Air Handlers
Commercial air-handling units routinely place double-width centrifugal impellers midway between sheet-metal side panels separated by more than a meter. Even minor belt tension from a variable-frequency drive sheave bows that long 40 mm fan shaft enough to overload rigid deep-groove units. Inside the 1208, the inner assembly pivots freely around the bearing center against the concave outer track, absorbing roughly 2.5 degrees of static misalignment and dynamic whip.
Because ball-to-raceway contact remains point-like rather than line contact, rolling resistance stays remarkably low. That translates into subdued acoustic signatures inside hospital, office, and cleanroom plenums where bearing hum travels down galvanized ductwork. Cage construction matters during continuous ventilation shifts: pressed steel retainers tolerate elevated air-stream temperatures, while glass-fiber reinforced polyamide cages offer quieter running up to roughly 120 °C continuous ceiling. Exact cage material, internal clearance (CN or C3), and tolerance grade are locked on the factory engineering print before production release.
1208 Cross-Reference & Plumbing Block Interchange Check
Facility engineers servicing split plummer blocks such as SNL 508 or cast-iron pillow housings frequently encounter multiple European and Japanese part numbers sharing the same 40 × 80 × 18 mm ISO 15 footprint:
| Brand / Standard | Cylindrical Bore | 1:12 Tapered Bore | Remarks |
|---|---|---|---|
| ZQM Bearings | 1208 | 1208K | Factory drawing confirms cage & clearance |
| SKF | 1208 / 1208 ETN9 | 1208 K / 1208 EKTN9 | E = enhanced internal ball complement; TN9 = polyamide cage |
| FAG / Schaeffler | 1208-TVH | 1208-K-TVH | TVH = glass-fiber reinforced polyamide retainer |
| NSK / NTN | 1208 | 1208K | Verify stamped steel vs polymer retainer suffix |
| Legacy GB Code | 1208 | 11208 | Historical Chinese cylindrical / tapered designation |
Dimensional Notice: Equivalency above covers ISO 15 boundary dimensions (40 × 80 × 18 mm) only and does not imply blind drop-in replacement. Internal ball count, polymer heat limits, and radial clearance vary across makers and must be checked against original equipment specifications.
HVAC Blower Mounting, SNL Pedestals & Belt-Drive Practice
Across commercial building industrial machinery installations, maintenance crews typically configure one 1208 position as locating using stabilizing rings inside a split housing while leaving the opposite pedestal free to float axially as the fan shaft warms up. When retrofitting commercial cold-drawn bar stock without machined shoulders, pairing 1208K with an H208 adapter sleeve simplifies axial positioning—tighten the locknut carefully so radial internal clearance is not wiped out during drive-up.
Notice that the 1208 handles moderate radial belt pull and modest aerodynamic thrust, yet it is never a substitute for a 22208 spherical roller bearing where heavy shock or thick particulate buildup unbalances an industrial rotor. Open 1208 units mounted inside split housings rely on clean lithium-complex grease and felt or labyrinth seals to keep condensation out of the raceways.
Specifying 1208 for Fan OEMs & Facility MRO Orders
Before placing an order or MRO restock request, send us five details: bore execution (straight 1208 vs 1:12 tapered 1208K with or without H208 sleeve), preferred cage polymer or stamped steel, radial clearance (CN or C3), operating ambient temperature near the fan scroll, and batch quantity. Our engineering desk confirms the exact drawing parameters—including dynamic and static ratings—before scheduling manufacturing or consolidated shipment.
Request a 1208 Technical Drawing & Quote
1208 Engineering Questions for Ventilation Maintenance
Related Selection & Comparison: Need a wider 23 mm radial footprint on the exact same 40 mm shaft? Compare 2208 (40 × 80 × 23 mm), verify 1:12 K adapter sleeve H208 in our Tapered Bore Calculator, or browse Self-Aligning Ball Bearings.
What shaft size fits a 1208K mounted with an H208 adapter sleeve?
While the straight-bore 1208 mounts directly onto a 40 mm journal, the 1208K features a 1:12 tapered bore designed to clamp onto a 35 mm smooth commercial shaft when paired with a metric H208 adapter sleeve.
Why choose 1208 over a 6208 deep-groove ball bearing on rooftop air handlers?
Both share the 40 × 80 × 18 mm boundary envelope, but a rigid 6208 tolerates only a few arc-minutes of shaft slope. Long sheet-metal fan housings routinely flex beyond that limit, making the self-aligning 1208 far more forgiving against premature raceway spalling.
Can a polyamide-caged 1208 operate inside smoke-extraction fans?
No. Standard polyamide retainers carry an upper continuous operating ceiling near 120 °C and soften rapidly in emergency smoke-exhaust streams. High-temperature duct fans require stamped steel or machined brass cages confirmed on the factory drawing.
Do the balls protrude past the 18 mm ring faces on the 1208?
On the narrow Series 12 size 1208, ball protrusion is generally minimal compared with heavier Series 13 or 23 units, though adjacent spacer sleeves and labyrinth seal rings should still be checked against the formal drawing before assembly.



