GE30ES-2RS Spherical Plain Bearing 30 × 47 × 22/18 mm

GE30ES-2RS sealed steel-on-steel spherical plain bearing (ISO 12240-1 Series E, 30 × 47 × 22/18 mm) built for compact forklift mast tilt-cylinder rod eyes and hydrostatic rear-axle steering linkages. Supplied with double-lip contact seals and relubrication passages; full sliding load ratings confirmed on factory drawing.

Conforming to ISO 12240-1 Dimension Series E, the GE30ES-2RS (GE 30 ES-2RS) radial spherical plain bearing fits a 30 mm pin bore inside a compact 47 mm outer diameter, pairing a 22 mm inner-ring width (B) with an 18 mm outer-ring width (C). Featuring hardened steel-on-steel sliding contact, annular relubrication channels, and integral -2RS double-lip contact seals, it is widely applied inside compact forklift mast tilt-cylinder rod eyes and hydrostatic steering linkages where short-stroke angular reversals occur thousands of times per warehouse shift.

GE30ES-2RS ISO 12240-1 Nominal Boundary Dimensions

Parameter Verified Specification Engineering Note
Designation GE30ES-2RS ISO 12240-1 Dimension Series E, sealed radial spherical plain bearing
Bore Diameter (d) 30 mm Nominal pin diameter
Outside Diameter (D) 47 mm Nominal rod-eye / clevis housing bore
Inner Ring Width (B) 22 mm Full spherical ball width across pin clamping faces
Outer Ring Width (C) 18 mm Single-fractured outer ring seating width
Sliding Contact Pair Hardened bearing steel / steel Phosphate and MoS₂ running-in treatment; requires periodic relubrication
Sealing & Lubrication -2RS lip seals + oil grooves & holes Double-sided elastomer contact seals; annular groove on inner & outer rings
Sliding Load Ratings, Clearance & Tilt Angle Confirmed on factory drawing Dynamic/static sliding capacity, radial clearance group & exact surface spec issued upon quotation

Sliding Contact Physics (p·v) & Outer-Ring Fracture Geometry

Unlike rolling-element joints, the GE30ES-2RS carries load across a conforming spherical steel-on-steel sliding interface treated with manganese phosphate and molybdenum disulfide (MoS₂) to aid initial running-in. Operational longevity is governed by specific contact pressure multiplied by sliding velocity (p·v) alongside disciplined grease replenishment—never by rolling fatigue life models. High-frequency small-angle oscillation in steering tie rods can squeeze grease out of the contact zone, making the ES annular groove and cross-drilled relubrication holes essential for pushing fresh lithium-complex EP grease straight onto the loaded hemisphere.

To assemble the hardened inner sphere inside the enveloping outer ring, the outer ring features a single radial fracture split. During press-fit into a forklift cylinder rod eye, mechanics must align this radial fracture plane at 90° to the primary radial hydraulic thrust axis so peak push-pull rod forces never wedge the split open or pinch the inner ball.

Compact Forklift Tilt-Cylinder & Hydrostatic Steering Fitment

Counterbalance forklifts, narrow-aisle reach trucks, and compact telehandlers pack dual mast tilt cylinders and tight rear-steer axles into narrow chassis cutouts where a 47 mm outer diameter leaves minimal rod-eye wall section. The 4 mm overhang between inner width (22 mm) and outer width (18 mm) lets the spherical ball tilt freely without clevis ears scraping the outer housing, absorbing welded-frame twist as loaded pallets travel over dock plates.

Warehouse concrete dust, tire-rubber fines, and washdown moisture quickly score unsealed plain bushings; the molded -2RS lip seals lock debris out while retaining fresh grease inside the 30 mm joint. Press the outer ring cleanly into the eye housing using a stepped sleeve contacting only the outer face, secure axially with circlips or shoulder steps, and orient the grease port opposite the main load zone. Explore industrial material-handling support at our equipment applications hub.

GE30ES-2RS Cross-Brand Designation Comparison

Brand / Standard Reference Designation ISO 12240-1 Series E Alignment (30 × 47 × 22/18 mm)
ZQM / GB/T 9163 GE30ES-2RS Steel-on-steel, phosphate/MoS₂ treated, relubrication holes, -2RS lip seals
SKF GE 30 ES-2RS Steel/steel radial spherical plain bearing, lip seals on both sides
INA / Schaeffler GE30-DO-2RS Series E steel-on-steel requiring maintenance (DO), dual lip seals (-2RS)
IKO GE30ES-2RS ISO Series E steel-on-steel sealed spherical plain bearing
Fluro GE 30 ES-2RS Steel/steel relubricatable, twin lip seals

Engineering Interchange Caution: The matrix reflects nominal ISO 12240-1 Series E boundary envelope parity (30 × 47 × 22/18 mm) only. Elastomer lip compound temperature range, internal radial clearance class (C2/CN/C3), exact sliding load ratings, and surface phosphating process differ across producers and must be validated against our factory drawing prior to OEM approval.

Ordering GE30ES-2RS for Cylinder OEMs & Forklift Fleets

When requesting factory pricing for GE30ES-2RS bearings, indicate your annual cylinder build or fleet maintenance volume, desired radial internal clearance group (standard CN or enlarged C3 for heavy press fits), and target seal elastomer temperature conditions. ZQM provides formal factory drawings verifying exact sliding load capacities and clearance tolerances prior to shipment—supporting sample qualification batches and recurring cylinder OEM supply. Submit your inquiry through our ZQM engineering quotation page.

GE30ES-2RS Frequently Asked Questions

Related Selection & Comparison: For heavier 40 mm excavator and loader pin joints, step up to GE40ES-2RS, browse all ISO 12240-1 sizes in Spherical Plain Bearings, or explore Construction Machinery.

Why does GE30ES-2RS list two width numbers (22 mm and 18 mm)?

The inner spherical ring measures B = 22 mm wide to seat snugly between clevis pin spacers, while the enveloping outer ring measures C = 18 mm wide to fit inside the hydraulic cylinder rod eye—creating built-in axial clearance so the joint can articulate freely without clevis interference.

How must the outer-ring radial fracture on GE30ES-2RS be positioned during press-fitting?

Always rotate the outer ring so its single radial assembly fracture sits at 90° to the main push-pull load line of the hydraulic cylinder or steering link. Placing the split in the loaded hemisphere risks local deformation, accelerated wear, and binding.

Does GE30ES-2RS require periodic greasing despite having -2RS seals?

Yes. Because GE30ES-2RS uses a hardened steel-on-steel sliding contact pair (ES), regular relubrication through its annular grooves and oil holes is mandatory to control p·v friction heat, prevent fretting corrosion under small-angle steering oscillation, and purge microscopic wear particles.

How can buyers verify exact sliding load ratings and clearance before ordering GE30ES-2RS?

Exact dynamic and static sliding capacities, radial clearance group (CN/C2/C3), permissible tilt angle, and phosphate/MoS₂ surface finish specifications are formally issued on the ZQM factory drawing upon quotation, alongside trial-lot options for hydraulic cylinder qualification.

Scroll to Top