GE70ES-2RS Spherical Plain Bearing 70 × 105 × 49/40 mm

GE70ES-2RS sealed steel-on-steel spherical plain bearing (ISO 12240-1 Series E, 70 × 105 × 49/40 mm) built for port container reach-stacker lift cylinders and shipboard cargo hatch-cover hydraulic actuators exposed to marine salt spray and heavy cyclic lifting. Sliding ratings confirmed on factory drawing.

Engineered to ISO 12240-1 Dimension Series E, the GE70ES-2RS (GE 70 ES-2RS) sealed radial spherical plain bearing carries a 70 mm heavy pin bore inside a 105 mm outside diameter, with an inner-ring width (B) of 49 mm and an outer-ring width (C) of 40 mm. Featuring hardened bearing-steel sliding contact treated with phosphate and MoS₂, relubrication grooves and oil holes in both rings, and robust -2RS double-lip seals, it serves demanding coastal container reach-stacker boom cylinders and shipboard hydraulic hatch-cover actuators operating in salt-laden maritime atmospheres.

GE70ES-2RS ISO 12240-1 Nominal Boundary Table

Dimension / Feature ISO 12240-1 Series E Spec Remarks
Designation GE70ES-2RS Sealed radial spherical plain bearing, ISO 12240-1 Series E
Bore Diameter (d) 70 mm Nominal actuator / boom pin diameter
Outside Diameter (D) 105 mm Nominal clevis / cylinder eye bore
Inner Ring Width (B) 49 mm Full spherical ball width across pin cheeks
Outer Ring Width (C) 40 mm Single-fractured outer ring seating width
Sliding Contact Pair Hardened bearing steel / steel Phosphate + MoS₂ surface finish; periodic marine-grade EP relubrication
Sealing & Lubrication -2RS double-lip seals + ES oil ports Dual elastomer contact seals + annular grooves & holes in both rings
Load Ratings, Clearance & Tilt Confirmed on factory drawing Dynamic/static sliding capacities, radial clearance group & coating spec issued at quote

Marine Cyclic Lifting (p·v) & Mandatory 90° Outer-Ring Split Rule

Container yard reach-stackers hoist 45-tonne intermodal boxes thousands of cycles per month, while bulk-carrier folding hatch covers swing slowly under immense hydraulic cylinder pressure against rolling seas. Because the GE70ES-2RS relies on direct steel-on-steel sliding rather than rolling tracks, operational endurance is determined by specific contact pressure × sliding velocity (p·v) together with water-resistant grease film maintenance.

To permit inner-ball insertion during manufacture, the outer ring features a single radial assembly fracture. Terminal maintenance engineers and ship-repair fitters must always align that radial fracture precisely at 90° to the primary hydraulic thrust vector when pressing the bearing into cylinder rod eyes or hatch hinges—placing the split along the load axis risks local ring spread and galvanic seawater seepage into the split seam.

Salt-Spray Corrosion Control on Ports & Vessel Weather Decks

Chloride-rich sea mist and green-water deck washdown rapidly pit unprotected carbon-steel pivot pins and bushings. The GE70ES-2RS defends its 70 mm sliding zone on two fronts: integral -2RS double-lip contact seals exclude wind-driven brine and dockside coal/ore dust across the full articulation angle afforded by its 9 mm width step (49 mm inner vs. 40 mm outer), while the ES annular lubrication groove allows crews to pack water-washout-resistant calcium-sulfonate complex marine EP grease completely around the sphere, purging salty moisture before corrosion initiates.

For automated terminal crane cylinders and vessel deck machinery where unscheduled downtime halts cargo operations, standardized ISO 12240-1 geometry simplifies global port spare stocking. See our maritime and port machinery support on the port & marine equipment solutions page.

GE70ES-2RS Cross-Reference Table for Port & Ship Spares

Manufacturer / Standard Equivalent Designation ISO 12240-1 Series E Match (70 × 105 × 49/40 mm)
ZQM / GB/T 9163 GE70ES-2RS Hardened steel/steel, phosphate/MoS₂ finish, oil grooves/holes, -2RS seals
SKF GE 70 ES-2RS Steel-on-steel radial spherical plain bearing, lip seals both sides
INA / Schaeffler GE70-DO-2RS Series E maintenance-type steel-on-steel (DO), twin lip seals
IKO GE70ES-2RS ISO Series E sealed steel-on-steel spherical plain bearing
Fluro GE 70 ES-2RS Relubricatable steel/steel joint bearing with -2RS lip seals

Maritime Replacement Notice: Designations listed above match strictly on nominal ISO 12240-1 Series E boundary dimensions (70 × 105 × 49/40 mm). Corrosion-inhibiting coatings, marine seal elastomer grades, radial clearance group (C2/CN/C3), and sliding load capacities differ across makers and are formally verified via ZQM factory drawing before shipyard or port-authority acceptance.

Procuring GE70ES-2RS for Terminal Fleets & Marine Cylinder Builders

When requesting a GE70ES-2RS quotation for reach-stacker rebuilds or shipboard hatch-cover refits, indicate your required quantity, housing press-fit class (CN vs. C3 radial clearance), and marine grease / corrosion-protection expectations. ZQM ships from our Wafangdian factory via Ningbo port consolidation with verified factory drawings covering sliding load ratings, clearance limits, and surface treatment. Contact our export specialists via the ZQM marine & industrial RFQ page.

GE70ES-2RS Port & Shipboard FAQ

Related Selection & Comparison: For 80 mm high-temperature steel-mill linkages, compare GE80ES-2RS, review port crane bearing guidance in Conveyors & Cranes, or view all Spherical Plain Bearings.

How does GE70ES-2RS resist saltwater corrosion on exposed shipboard hatch-cover actuators?

Dual -2RS contact lip seals shield the hardened steel-on-steel sliding faces from direct salt spray, while its ES annular grease groove and oil holes allow deck crews to periodically purge water-resistant marine EP grease through the joint to displace moisture.

Why is outer-ring fracture alignment critical on 70 mm reach-stacker boom cylinders?

The outer ring’s single radial fracture must sit 90° away from the main hydraulic cylinder thrust axis. Aligning the split in the loaded lifting zone under 45-tonne container loads risks distorting the outer ring and trapping brine inside the seam.

What grease type is recommended for GE70ES-2RS in coastal port container terminals?

Because sliding service life depends on p·v contact film stability and corrosion defense, use a high-load water-resistant marine EP grease (such as calcium-sulfonate complex with MoS₂) replenished via the ES relubrication ports on a fixed port-maintenance schedule.

Will ZQM supply formal engineering drawings confirming GE70ES-2RS load ratings and clearances?

Yes. Dynamic and static sliding capacities, radial clearance group, tilt angle, and phosphate/MoS₂ coating specifications are confirmed on the formal ZQM factory drawing issued with your quotation, supporting both vessel dry-dock kits and OEM cylinder production.

Scroll to Top