GE120ES-2RS Spherical Plain Bearing 120 × 180 × 85/70 mm

GE120ES-2RS large-bore sealed steel-on-steel spherical plain bearing (ISO 12240-1 Series E, 120 × 180 × 85/70 mm) built for hydroelectric spillway radial-gate hydraulic trunnions and heavy offshore jack-up linkages handling colossal ultra-slow static clamping forces. Exact sliding specs confirmed on factory drawing.

At the heavyweight upper tier of ISO 12240-1 Dimension Series E, the GE120ES-2RS (GE 120 ES-2RS) sealed radial spherical plain bearing accommodates a formidable 120 mm trunnion pin within a 180 mm outside diameter, pairing an 85 mm inner-ring width (B) with a 70 mm outer-ring width (C). Constructed with hardened bearing-steel sliding faces treated with phosphate and MoS₂, deep annular lubrication channels in both rings, and robust -2RS double-lip seals, it serves hydroelectric dam spillway radial-gate hoist linkages, lock-gate hydraulic rams, and heavy offshore jack-up positioning actuators bearing immense, ultra-slow static clamping forces.

GE120ES-2RS ISO 12240-1 Nominal Boundary Dimensions

Specification ISO 12240-1 Series E Value Civil & Offshore Engineering Note
Designation GE120ES-2RS Large-bore ISO 12240-1 Series E sealed radial spherical plain bearing
Bore Diameter (d) 120 mm Nominal heavy trunnion / hoist pin bore
Outside Diameter (D) 180 mm Nominal actuator clevis / trunnion block bore
Inner Ring Width (B) 85 mm Full spherical inner ring axial span
Outer Ring Width (C) 70 mm Single-fractured outer ring seating width
Sliding Contact Pair Hardened bearing steel / steel Phosphate + MoS₂ surface finish; multi-year planned EP greasing
Sealing & Lubrication -2RS contact lip seals + ES oil grooves Double-sided seals; deep annular grooves & holes in both rings
Load Ratings, Clearance & Tilt Confirmed on factory drawing Dynamic/static sliding load ratings, radial clearance & surface spec issued at quote

Ultra-Slow Static Clamping (p·v), Long-Term Greasing & 90° Split Rule

Spillway tainter-gate hydraulic hoists and offshore jack-up leg-locking mechanisms remain virtually motionless for weeks or months under monumental hydrostatic or structural clamping loads before creeping slowly through a single opening stroke. Because rolling elements would suffer severe static indentation and false brinelling under prolonged standstill loads, steel-on-steel spherical sliding joints are the engineering standard here—governed strictly by specific contact pressure × sliding velocity (p·v) and long-term oxidation-resistant boundary lubrication.

Its massive 180 mm outer ring carries a single radial assembly fracture. Civil-hydromechanical erectors and offshore shipyard riggers must verify that this radial fracture is rotated strictly 90° away from the primary hydrostatic or hoist load line prior to press-fitting, preserving uniform hoop support around the 120 mm loaded hemisphere across decades of service.

Hydroelectric Spillway & Offshore Environmental Resilience

Dam spillway trunnions sit in perpetual mist, silt-laden flood spray, and seasonal freeze-thaw cycles, while offshore platform linkages confront driving salt spray and structural foundation settling. The generous 15 mm width differential (85 mm inner vs. 70 mm outer) allows wide angular self-alignment as concrete piers shift microscopically or long hydraulic cylinders deflect under wind and wave surges. Twin -2RS elastomer lip seals guard the hardened steel sliding interface against river silt and marine brine, while high-capacity ES oil grooves let maintenance teams execute scheduled multi-year relubrication flushes using water-insoluble marine/hydro EP greases without dismantling 120 mm pins.

Discover how ZQM serves heavy civil infrastructure, hydropower, and offshore contractors on our heavy infrastructure & offshore industry page.

GE120ES-2RS Cross-Reference Equivalents

Brand / Standard Equivalent Designation ISO 12240-1 Series E Match (120 × 180 × 85/70 mm)
ZQM / GB/T 9163 GE120ES-2RS Hardened steel/steel, phosphate & MoS₂ treated, oil grooves/holes, -2RS seals
SKF GE 120 ES-2RS Steel-on-steel radial spherical plain bearing, twin contact lip seals
INA / Schaeffler GE120-DO-2RS Series E maintenance-required steel/steel (DO), double-sided lip seals
IKO GE120ES-2RS ISO 12240-1 Series E sealed steel-on-steel joint bearing
Fluro GE 120 ES-2RS Relubricatable steel/steel spherical plain bearing, -2RS seals

Project Specification Disclaimer: Designations listed above match strictly on nominal ISO 12240-1 Series E boundary envelope (120 × 180 × 85/70 mm). Critical civil-dam and offshore installations require formal pre-order approval of exact sliding load capacities, radial clearance group (C2/CN/C3), seal elastomer aging resistance, and phosphate/MoS₂ coating specs via ZQM’s confirmed factory drawing.

Procuring GE120ES-2RS for Hydropower Projects & Offshore Contractors

When preparing a tender or rehabilitation RFQ for GE120ES-2RS bearings, provide your project quantity, housing press-fit tolerance & ambient temperature (for CN vs. C3 clearance verification), and QA inspection witness or documentation scope. ZQM pairs our Wafangdian heavy-bearing manufacturing facility with export project logistics, issuing confirmed factory engineering drawings alongside formal pricing. Reach our heavy-project specialists through our project engineering quotation portal.

GE120ES-2RS Hydropower & Offshore FAQ

Related Selection & Comparison: Compare 100 mm mining strut sizing via GE100ES-2RS, review dimensional & NDT verification in our Quality Control Lab, or browse all ISO 12240-1 models in Spherical Plain Bearings.

Why is a steel-on-steel GE120ES-2RS preferred on hydroelectric dam radial-gate hoist linkages?

Spillway gates sit stationary under colossal static hydrostatic loads for long periods before moving very slowly. The GE120ES-2RS distributes static pressure across a wide hardened spherical contact zone without static rolling indentation, while accommodating concrete-pier and hoist misalignment.

How must the 180 mm outer-ring fracture on GE120ES-2RS be positioned during dam-gate installation?

Always rotate the single radial fracture in the outer ring to 90° relative to the primary hoist tension or hydrostatic radial load axis. Placing the split in the primary load zone risks distorting the outer ring under colossal clamping forces.

What maintenance planning applies to GE120ES-2RS bearings operating on multi-year civil infrastructure cycles?

Establish scheduled preventive relubrication intervals using water-resistant, oxidation-stable EP grease pumped through the ES annular grooves and oil holes before seasonal floodgate trials, ensuring fresh boundary lubrication controls p·v startup friction and excludes moisture.

Will ZQM supply project-ready factory drawings confirming GE120ES-2RS sliding capacities prior to contract award?

Yes. Dynamic and static sliding load ratings, radial clearance group, permissible tilt angle, and phosphate/MoS₂ coating specifications are formally confirmed on the ZQM factory drawing issued with your quotation, with standard dimensional and hardness inspection documentation provided upon shipment.

Scroll to Top