Constructed to ISO 12240-1 Dimension Series E, the heavy-duty GE100ES-2RS (GE 100 ES-2RS) sealed radial spherical plain bearing fits a massive 100 mm structural pin bore inside a 150 mm outside diameter, uniting a 70 mm inner-ring width (B) with a 55 mm outer-ring width (C). Combining hardened bearing-steel sliding contact treated with phosphate and MoS₂, wide annular lubrication channels, and heavy-duty -2RS double-lip seals, it is engineered for underground mining haul-truck hydro-pneumatic suspension struts, dump-body hoist cylinders, and LHD loader center articulations subjected to brutal off-road impact peaks.
GE100ES-2RS ISO 12240-1 Nominal Boundary Specification
| Parameter | ISO 12240-1 Series E Nominal | Heavy Mining Context |
|---|---|---|
| Designation | GE100ES-2RS | ISO 12240-1 Dimension Series E, heavy sealed radial spherical plain bearing |
| Bore Diameter (d) | 100 mm | Nominal heavy suspension / hoist pin bore |
| Outside Diameter (D) | 150 mm | Nominal strut / hoist cylinder eye bore |
| Inner Ring Width (B) | 70 mm | Wide spherical inner ring span |
| Outer Ring Width (C) | 55 mm | Single-fractured outer ring width |
| Sliding Contact Pair | Hardened bearing steel / steel | Phosphate + MoS₂ running-in layer; periodic EP MoS₂ greasing required |
| Sealing & Relubrication | -2RS double-lip seals + ES grooves | Heavy contact seals + annular grooves & oil holes in both rings |
| Load Ratings, Clearance & Tilt | Confirmed on factory drawing | Dynamic/static sliding capacities, radial clearance group & coating verified at quote |
Extreme Off-Road Shock (p·v), 100 mm Pin Deflection & 90° Split Rule
Fully laden 50-to-65-tonne underground mine trucks pounding up wet blasted-rock ramps generate violent shock spikes through front and rear suspension struts while twisting main frames heavily during turns. Even a thick 100 mm alloy-steel pin deflects elastically under such peaks; the GE100ES-2RS’s 15 mm width difference between inner width (70 mm) and outer width (55 mm) grants wide angular self-alignment so pin bending never edge-loads the cylinder eye or shears retaining plates. Service endurance rests entirely on steel-on-steel sliding physics—governed by specific contact pressure × sliding velocity (p·v) and pressurized MoS₂ grease retention—rather than rolling-element contact fatigue.
Its outer ring incorporates a single radial fracture for sphere insertion. Mine-shop fitters rebuilding suspension struts or hoist cylinders must orient this radial fracture exactly at 90° to the primary vertical suspension or dump-hoist load vector so severe rock-strike impacts never wedge the outer-ring split open.
Underground Mine Slurry & Blast-Dust Defense
Underground haulage drifts combine acidic mine drainage water, sharp blasted-quartz slurry, and fine diesel/rock dust that rapidly abrade exposed suspension linkages. The GE100ES-2RS pairs heavy -2RS double-lip seals with deep ES internal oil grooves and cross-holes so auto-lube injectors can continuously charge the 100 mm sliding interface with 5%-MoS₂ mining EP grease, flushing abrasive muck outward before it can score the hardened sphere.
Standardizing on verified ISO 12240-1 Series E geometry lets mine maintenance planners consolidate spare inventory across dump hoists, steering cylinders, and suspension struts. Explore our underground and open-pit mining support on our mining equipment MRO page.
GE100ES-2RS Mining Fleet Cross-Reference
| Manufacturer / Code | Reference Designation | Series E Alignment (100 × 150 × 70/55 mm) |
|---|---|---|
| ZQM / GB/T 9163 | GE100ES-2RS | Hardened steel/steel, phosphate/MoS₂ treated, oil grooves/holes, -2RS seals |
| SKF | GE 100 ES-2RS | Steel-on-steel radial spherical plain bearing, double-sided lip seals |
| INA / Schaeffler | GE100-DO-2RS | Series E maintenance-type steel-on-steel (DO), twin contact seals |
| IKO | GE100ES-2RS | ISO 12240-1 Series E sealed steel-on-steel joint bearing |
| Fluro | GE 100 ES-2RS | Relubricatable steel/steel spherical plain bearing, -2RS lip seals |
Mine-Site Interchange Disclaimer: Equivalents shown above align solely on nominal ISO 12240-1 Series E boundary dimensions (100 × 150 × 70/55 mm). Actual sliding load ratings, radial internal clearance group (C2/CN/C3), heavy-duty seal compound durability, and surface phosphating specifications differ among producers and must be verified on ZQM’s formal factory drawing prior to fleet rollout.
Procuring GE100ES-2RS for Mine-Site Fleets & Heavy Cylinder Rebuilders
When requesting a GE100ES-2RS quotation for haul-truck suspension or hoist-cylinder rebuild programs, specify your fleet rebuild quantity, strut-eye housing fit interference (for CN vs. C3 radial clearance confirmation), and underground humidity/temperature range. ZQM supplies verified factory engineering drawings with every formal quote and packs heavy bearings in moisture-sealed export crates suited for remote mine-site logistics. Reach our mining MRO desk via our ZQM quote & engineering contact page.
GE100ES-2RS Mining Haul-Truck FAQ
Related Selection & Comparison: For ultra-large 120 mm dam-gate and offshore trunnions, step up to GE120ES-2RS, review haul-truck & mining shock durability in Mining & Crushing, or browse Spherical Plain Bearings.
Why do underground haul-truck suspension struts rely on GE100ES-2RS rather than rigid cylindrical bushings?
Under massive off-road shock loads, 100 mm pins bend and truck chassis twist dramatically. The GE100ES-2RS’s spherical sliding geometry and 70/55 mm dual width allow free multi-axis tilting, eliminating catastrophic edge loading on cylinder eyes and strut rods.
Which orientation is mandatory for the GE100ES-2RS outer-ring split inside a suspension strut eye?
Rotate the single radial fracture in the outer ring to sit 90° away from the primary vertical suspension or hoist-cylinder thrust axis. Aligning the split in the loaded vertical zone invites ring distortion and rapid joint seizure under rock impacts.
Can GE100ES-2RS connect directly to an underground haul truck’s automatic centralized greasing system?
Yes. Its ES outer-ring annular lubrication groove and cross-drilled oil holes distribute centralized high-load MoS₂ EP grease uniformly across the hardened steel-on-steel sliding surface while helping the -2RS lip seals reject acidic mine slurry.
How does ZQM confirm exact sliding load ratings and clearance before shipping GE100ES-2RS to mine sites?
Every formal quotation is accompanied by a confirmed ZQM factory drawing specifying dynamic and static sliding capacities, radial clearance class, tilt angle, and phosphate/MoS₂ coating details, backed by standard factory dimensional and hardness inspection sheets.



