A four-point contact ball bearing is a single-row angular contact ball bearing whose raceway grooves are machined to form a 35 deg contact angle capable of carrying pure axial load in either direction—or combined loads dominated by thrust—within an envelope far narrower than a back-to-back pair of single-row angular contact bearings.

To allow assembly of deep gothic-arch raceways and a full complement of large balls inside a solid brass cage, one ring—most commonly the two-piece inner ring in standard QJ designs and ZQM’s QJF catalogue specification—is split axially into two halves (always confirm split-ring location on the bearing drawing). That design solves axial space bottlenecks on rolling-mill chocks, industrial gearboxes, and large motor shafts, yet also creates two frequent shop-floor traps: accidental radial preloading and non-standard housing outer diameters.
1. QJ / QJF Type Prefixes & MA vs MB Cage Guidance
Before replacing a locating thrust ball bearing, separate the series/type prefix (QJ / QJF) from the cage-guidance suffix (MA / MB):
- QJ / MA design (e.g., QJ…MA): Series prefix
QJuses a two-piece split inner ring; theMAsuffix specifies a one-piece machined solid brass cage centered on the outer ring lands. - QJF / MB design (e.g., 116756 / QJF1058MB): While certain GB/T 294
QJFdrawing conventions use a split outer ring, ZQM’s catalogue116756 / QJF1058MBuses a two-piece split inner ring paired with an inner-ring-centered machined solid brass cage (MB), widely used on heavy rolling-mill chocks and gearbox locating positions. Always check the drawing when cross-referencingQJFspares. - Full-width axial clamp: Whichever ring is split into two halves (typically the inner ring) MUST be clamped firmly side-to-side by a locknut, rigid spacer, or end cover so the split line never opens under reversing thrust.
- Two-piece inner ring supports bidirectional thrust
- Outer ring needs radial clearance when paired with NJ
- ZQM QJF1058MB (Legacy 116756): 280 x 419.5 x 65 mm | a = 245 mm | da ≥ 298 | Da ≤ 402
- Standard Metric 1056 Size (e.g., QJ1056): 280 x 420.0 x 65 mm (+0.50 mm OD difference)
- Always micrometer housing bore + confirm anti-rotation slot
2. How NJ + QJ / QJF Arrangements Work Together (Radial Clearance Rule)
On high-load gear drives and roll necks, radial capacity comes from a cylindrical roller bearing—such as NJ326EM (130 x 280 x 58 mm, Fw = 167 mm, Cr = 615 kN) or NJ2320M (100 x 215 x 73 mm, Fw = 129.5 mm, Cr = 440 kN). For bidirectional vs unidirectional axial restraint mechanics, also review our NU vs NJ vs N vs NUP guide.
When a QJ or QJF four-point contact ball bearing is placed beside a cylindrical roller bearing (NU, NJ, or FCDP) to act solely as an axial locating bearing, follow two non-negotiable housing rules:
- Leave radial clearance around the QJ/QJF outer ring: Machine or specify the housing bore slightly oversize relative to the QJ/QJF outer diameter (or rely on verified radial play in the chock) so the ball bearing carries zero radial shaft load. If squeezed radially, balls bind on all four points simultaneously, generating skidding and rapid raceway spalling.
- Prevent outer-ring rotation: Because the outer ring sits radially loose in the housing, use locating slots or anti-rotation notches in the outer ring (where specified by drawing) pinned to the housing cover, while clamping both inner-ring halves tightly on the rotating shaft.
3. Real-World Dimensional Pitfall: 116756 / QJF1058MB (419.5 mm) vs Standard 420.0 mm
In ZQM’s 259-page technical catalogue, legacy designation 116756 maps directly to current catalogue model QJF1058MB. Its verified catalogue data highlights why engineers must never round up an OD to match standard metric tables:
| Parameter | ZQM QJF1058MB (Legacy 116756) | Companion Radials (NJ Example) |
|---|---|---|
| Bore diameter (d) | 280 mm | NJ326EM: 130 mm | NJ2320M: 100 mm |
| Outside diameter (D) | 419.5 mm (non-standard!) | NJ326EM: 280 mm | NJ2320M: 215 mm |
| Width (B) | 65 mm | NJ326EM: 58 mm | NJ2320M: 73 mm |
| Dynamic / Static Load (Cr / Cor) | 553 kN / 1,060 kN | NJ326EM: 615 / 735 kN | NJ2320M: 440 / 630 kN |
| Grease / Oil Limiting Speed | 950 r/min / 1,400 r/min | NJ326EM: 1,800 / 2,200 r/min |
| Abutment & Load Center | da min 298 | Da max 402 | a = 245 mm | ra max 3 mm | NJ326EM: db min 149 | Da max 258 | ra max 3 mm |
| Minimum Chamfer (r1,2min) & Mass | 4.0 mm | 33.6 kg | NJ326EM: 4 mm (19.5 kg) | NJ2320M: 3 mm (13.5 kg) |
Notice that 419.5 mm OD on QJF1058MB / 116756 sits just 0.50 mm below a standard 280 x 420 x 65 mm QJ1056 bearing! Purchasing a standard 420.0 mm outer diameter to put inside a rolling-mill chock bored for 116756 turns intentional radial clearance into a heavy interference jam—forcing the ball bearing to absorb radial mill loads and burning up the unit quickly.
4. Pre-Order Checkpoints for QJ / QJF Replacements
- Measure both the actual bearing OD and housing bore with an inside micrometer—especially when legacy code
116756orQJF1058MBappears on the BOM. - Check whether the outer ring requires axial locating notches/slots (
N2or custom anti-rotation keyways) to stop housing spin. - Confirm shaft shoulder height (
da min = 298 mmon QJF1058MB) and maximum fillet radius (ra max = 3 mm) so the split inner ring seats cleanly.
Contact ZQM Bearings with your bearing designation, housing bore measurement, and anti-rotation slot drawing to verify exact QJ/QJF configuration and delivery.
Frequently Asked Questions
1. Can a QJ or QJF bearing run under pure radial load without axial load?
No. A four-point contact ball bearing requires an axial load exceeding radial load thresholds so balls contact only two opposing raceway points at a time. Pure radial loading causes simultaneous 3- or 4-point ball contact, sliding friction, and early heat failure.
2. Why is the inner ring split on QJ and QJF bearings?
Splitting the inner ring into two halves lets a full complement of large-diameter balls and a one-piece solid brass cage be assembled into deep, steep 35-degree Gothic-arch raceways capable of handling bidirectional thrust.
3. Are 116756 (QJF1058MB) and QJ1056 directly interchangeable?
No. While bore (280 mm) and width (65 mm) match, QJF1058MB / 116756 has a special 419.5 mm OD compared to 420.0 mm on standard 1056 bearings. Always verify housing bore clearance and anti-rotation slot layout first.
4. When pairing NJ and QJ/QJF on the same shaft end, what clearance must the QJ outer ring have?
The QJ/QJF outer ring must sit radially loose in the housing bore—typically with deliberate radial clearance and pinned anti-rotation slots—so only the NJ or FCDP cylindrical bearing carries radial forces while QJ/QJF locates the shaft axially.

