NJ226EM Cylindrical Roller Bearing Overview
Designed with two outer-ring integral ribs and one inner-ring locating flange on a straight cylindrical bore, NJ226EM (130 × 230 × 40 mm, 7.38 kg) locates a 130 mm shaft axially in one direction while sustaining high speed. Reinforced E-series rollers and a machined brass cage deliver Cr = 290 kN, Cor = 410 kN, Fw = 153.5 mm, and speeds up to 2,200 rpm grease / 2,800 rpm oil.
NJ226EM Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 130 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 230 mm |
| Boundary Dimensions & Weight | Width (B) | 40 mm |
| Boundary Dimensions & Weight | Roller set under-raceway diameter (Fw) | 153.5 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 7.38 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 290 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 410 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 2200 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 2800 rpm |
| Abutment & Fillet Dimensions | Shaft abutment reference diameter (db) | 146 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 212 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 3 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2.5 mm |
| Abutment & Fillet Dimensions | Maximum flange fillet radius (rb) | 2.5 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Designation Breakdown & 130 mm Bore Selection
Key execution codes for NJ226EM and engineering comparison across 130 mm bore catalogue alternatives:
| Attribute | Code / Option | Engineering Notes |
|---|---|---|
| NJ / NU & EM Execution | NJ226EM |
Outer ring 2 ribs, inner ring 1 rib (single-direction axial locating); reinforced E rollers; machined brass cage (M); straight cylindrical bore |
| Internal Clearance | C0 (Normal) / C3 | Select C3 radial clearance when heavy shaft interference fits or 2,200+ rpm heat reduce operating play |
| Under-Roller Envelope | Fw = 153.5 mm | Straight-bore inner raceway allows separable mounting; Ew and Db/da: Contact us for specifications |
Sharing the 130 × 230 × 40 mm envelope with floating NU226EM (Cr 345 kN), this single-ribbed unit adds one-direction axial shaft positioning; stepping up to NJ326EM (280 × 58 mm) raises Cr to 615 kN.
| Catalogue Unit | Envelope & Mass | Ratings & Grease Limit |
|---|---|---|
| NJ226EM (Current) | 130 × 230 × 40 mm · 7.38 kg | Cr 290 kN · C0r 410 kN · 2,200 rpm |
| NU226EM | 130 × 230 × 40 mm · 7.90 kg | Cr 345 kN · C0r 425 kN · 2,200 rpm |
| NJ326EM | 130 × 280 × 58 mm · 19.5 kg | Cr 615 kN · C0r 735 kN · 1,800 rpm |
| NJ2326EM | 130 × 280 × 93 mm · 28.9 kg | Cr 920 kN · C0r 1,230 kN · 1,800 rpm |
Brand Cross-Reference & Interchangeability
Manufacturer designations sharing the 130 × 230 × 40 mm nominal ISO boundary envelope (full product catalog):
| Manufacturer | Reference Code | Verification Scope |
|---|---|---|
| ZQM Bearings | NJ226EM |
Machined brass cage cylindrical unit per ISO 15 boundary dimensions |
| SKF | NJ 226 ECM | Reinforced cylindrical design with machined brass cage |
| FAG / Schaeffler | NJ226-E-XL-M1 | X-life cylindrical series with M1 solid brass cage |
| NSK | NJ226EM | High-capacity cylindrical series with brass cage |
| NTN | NJ226EG1 | Machined brass cage industrial execution |
Engineering Interchange Disclaimer: Cross-reference for identification only. Verify interchangeability with engineering drawings. Listed references share nominal ISO boundary dimensions (130 × 230 × 40 mm) only; internal geometry, cage execution, and load ratings vary by manufacturer.
Industrial Applications & Mounting Guidance (130 mm Shaft Class)
Primary machinery roles and field mounting practices matched to this 130 × 230 × 40 mm assembly:
| Target Machinery | Operating Duty Profile | Mounting & Lubrication Practice |
|---|---|---|
| Medium AC Electric Motor Drive Ends | Radial belt or coupling forces up to 2,800 rpm oil / 2,200 rpm grease | Separable straight-bore inner ring presses cleanly onto motor shafts before stator insertion |
| Industrial Centrifugal Pump and Compressor Shafts | High radial stiffness with controlled single-direction impeller thrust | Pair with an opposite-facing NJ unit or NU226EM floating support on the non-drive end |
| Medium Helical Gearbox Intermediate Spindles | Rapid gear-mesh vibration in tight 40 mm axial width | One-piece machined brass M cage prevents pocket fatigue under cyclic speed reversals |
For reliable service life under ISO 281 fatigue calculations, maintain clean oil filtration, monitor housing temperature stabilization after initial run-in, and verify shaft journal roundness and shoulder squareness against the published abutment geometry before final press or sleeve installation. Post-mount feeler gauge measurements (on applicable radial structures) confirm mounted residual radial clearance—distinguishing it from final operating clearance under thermal equilibrium—while export batches include protective rust-inhibitor coating, individual VCI wrapping, and heavy-duty plywood crating tailored to sea or air transit.
Pre-Order Engineering Checklist
Confirm these three verification checkpoints with our engineering desk prior to scheduling factory dispatch for this 130 × 230 × 40 mm model:
| Checkpoint | Parameters to Confirm | Engineering Purpose |
|---|---|---|
| 1. Code & Clearance | Specify NJ226EM, C0/C3/C4 play, and straight bore |
Aligns mounted internal play with shaft interference and running ΔT |
| 2. Shoulder & Fit Limits | Verify db 146 mm, Da 212 mm, ra 2.5 mm; Db/da: Contact us for specifications | Prevents chamfer interference and inner-ring creep |
| 3. Quantity & QC Scope | Unit mass 7.38 kg; state batch qty, EXW/FOB/CIF terms, and CMM/UT/hardness needs | Confirms pallet crating, MOQ lead time, and inspection records |
Frequently Asked Questions
What are the dimensions and mass of NJ226EM?
Catalogue specs list 130 mm straight cylindrical bore, 230 mm outside diameter, 40 mm width, under-roller diameter Fw = 153.5 mm, and 7.38 kg mass.
How does this single-rib unit differ from NU226EM?
It has one inner-ring rib to locate the shaft axially in a single direction, whereas NU226EM has a ribless inner ring for pure axial float. Contact us for specifications on unquoted Db, da, or Ew values.
Which shoulder and fillet limits are published for this 130 mm model?
Published limits are db min = 146 mm, Da max = 212 mm, chamfer r1,2/r3,4 min = 3 mm, and fillet ra/rb max = 2.5 mm; Contact us for specifications regarding Db and da shaft step clearances.
When should C3 clearance and CMM inspection be requested for 130 mm motor shafts?
Medium 130 mm motor and pump shafts running near 2,200–2,800 rpm under heavy press fits typically require C3 radial clearance to preserve oil-film thickness. Confirm MOQ, export lead time, and CMM/hardness/UT inspection sheets with ZQM.








