NU228EM Non-Locating Cylindrical Roller Bearing Overview
Purpose-built as a floating-end bearing with two integral outer-ring flanges and a smooth, ribless inner ring on a straight cylindrical bore, NU228EM (NU 228 EM, 140 × 250 × 42 mm, Fw = 169 mm, mass 9.36 kg) allows bidirectional internal axial displacement within permissible limits so heated shafts expand freely without inducing parasitic thrust. Verified in ZQM Bearings’ factory catalogue, it carries Cr = 395 kN dynamic load, C0r = 515 kN static load, and speeds up to 2,400 rpm (grease) / 3,000 rpm (oil).
NU228EM Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 140 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 250 mm |
| Boundary Dimensions & Weight | Width (B) | 42 mm |
| Boundary Dimensions & Weight | Roller set under-raceway diameter (Fw) | 169 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 9.36 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 395 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 515 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 2400 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 3000 rpm |
| Abutment & Fillet Dimensions | Shaft abutment reference diameter (db) | 157 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 232 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 3 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2.5 mm |
| Abutment & Fillet Dimensions | Maximum flange fillet radius (rb) | 2.5 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
NU228EM Floating-End Geometry & 140 mm Bore Comparisons
Unlike locating designs, the NU228EM inner ring has zero retaining ribs—the cylindrical rollers glide axially along the wide inner raceway inside the bearing itself rather than forcing outer rings to creep inside the housing bore. That ISO 15 boundary-standardized NU non-locating principle makes NU228EM the classic floating partner to a locating bearing at the opposite end of a 140 mm shaft. Within ZQM’s catalogue nomenclature, E identifies reinforced roller geometry for higher radial capacity and M denotes a machined solid brass cage (confirm exact cage execution on drawing/purchase order). Explore rib arrangements and clearance guidance in our cylindrical roller NJ / NU / NUP technical guide.
| 140 mm Bore Option | Boundary Size & Weight | Capacity & Duty Trade-Off |
|---|---|---|
| NU228EM (Selected) | 140 × 250 × 42 mm · 9.36 kg | Cr 395 kN · C0r 515 kN · Compact floating end (2,400 rpm grease) |
| NJ228EM | 140 × 250 × 42 mm · 9.43 kg | Cr 395 kN · C0r 515 kN · Adds single-direction axial rib location |
| NU2228EM | 140 × 250 × 68 mm · 15.9 kg | Cr 550 kN · C0r 790 kN · +39% Cr inside same 250 mm OD housing |
| NU328EM | 140 × 300 × 62 mm · 23.7 kg | Cr 665 kN · C0r 880 kN · +68% Cr where 300 mm housing OD fits |
Brand Cross-Reference & Equivalent Designations
Major international bearing designations sharing the 140 × 250 × 42 mm ISO 15 envelope and NU flangeless inner-ring architecture (consult our ISO cross-reference verification article when replacing legacy units):
| Brand | Comparable ISO Designation | Pre-Substitution Engineering Check |
|---|---|---|
| ZQM Bearings | NU228EM / NU228EM C3 |
Straight cylindrical bore, Fw = 169 mm, reinforced E-series geometry |
| SKF | NU 228 ECM / NU 228 ECML/C3 | Machined brass cage EC series; confirm axial displacement limit & C3 code |
| FAG / Schaeffler | NU228-E-XL-M1 / NU228-E-M1-C3 | E-XL / M1 machined brass cage series; confirm clearance and housing fit |
| NSK | NU228EM / NU228EMC3 | E-design reinforced cylindrical roller; check Fw = 169 mm & chamfer radii |
| NTN | NU228E / NU228EG1C3 | E-series with G1 solid brass cage; verify internal clearance class |
ISO Nominal Boundary Disclaimer: Cross-references above represent matching ISO 15 nominal boundary dimensions (140 × 250 × 42 mm) only and do not guarantee drop-in functional interchangeability. Never intermix separable inner rings and outer-ring/roller assemblies from different manufacturers without confirming Fw (169 mm), permissible axial displacement, and radial clearance.
Industrial Applications & Floating-End Duty
Because NU228EM absorbs shaft thermal elongation internally while supporting tight interference fits on both rings, it is widely deployed at floating shaft ends in mining fans, crushers, and quarry drives as well as electric motors and rolling mills (explore all ZQM industrial applications):
| Floating-End Machine Position | Why NU Non-Locating Design Is Chosen | Service & Fit Guidance |
|---|---|---|
| High-Output Electric Motor & Generator Floating Ends | Long copper/steel rotors lengthen noticeably during continuous load runs | Pair NU228EM at the drive or floating end with a deep-groove or angular-contact locating bearing opposite |
| Industrial Induced-Draft Fans, Blowers & Compressors | Hot gas streams create steep thermal expansion between impeller and pedestal | Allows interference fits on both inner and outer rings without outer-ring fretting in the housing |
| Multistage Gearbox Intermediate Floating Shafts | High radial gear reaction in narrow 42 mm axial bay at up to 3,000 rpm oil | Separable flangeless inner ring simplifies vertical housing split assembly and shaft extraction |
| Paper Dryer Cylinders & Steel Mill Table Rolls | Long roller span subject to steam heat or hot slab radiation | Confirm shaft thermal growth stays strictly within permissible axial displacement before finalizing design |
Ordering NU228EM & Floating-End Verification Checklist
Supplied directly from ZQM Bearings’ Wafangdian factory network with Ningbo export consolidation and Shanghai warehouse dispatch, NU228EM is available for single-unit trials, mixed-SKU maintenance kits, and scheduled OEM programs. Review three checks before submitting your RFQ:
| Verification Step | Parameters to Confirm | Preventive Benefit |
|---|---|---|
| 1. Non-Locating Role & Clearance | Confirm opposite shaft end carries axial thrust; specify NU228EM CN or C3 clearance |
Prevents unconstrained axial shaft wander and compensates shaft-to-housing temperature rise |
| 2. Displacement & Shoulder Fit | Verify thermal expansion budget plus db min 157 mm, Da max 232 mm, ra/rb max 2.5 mm, Fw 169 mm | Prevents roller run-off beyond inner raceway edge and avoids fillet interference |
| 3. Batch Volume & Logistics | Unit mass 9.36 kg; specify order quantity, Incoterms (EXW/FOB/CIF), and QC report needs | Aligns factory lead time, export anti-rust packing, and dimensional/hardness inspection docs |
Frequently Asked Questions (FAQ)
What are the boundary dimensions, Fw, and reference weight of NU228EM?
Per ZQM Bearings’ online factory catalogue, NU228EM measures 140 mm bore × 250 mm outside diameter × 42 mm width with a roller envelope diameter Fw = 169 mm and reference mass of 9.36 kg. Rated capacities are Cr = 395 kN dynamic and C0r = 515 kN static, with limiting speeds of 2,400 rpm (grease) and 3,000 rpm (oil).
Can NU228EM carry any axial thrust load, or is a separate locating bearing mandatory?
No—because its straight-bore inner ring has no retaining ribs, NU228EM supports pure radial load only and cannot locate a shaft axially. Every shaft supported by NU228EM requires a dedicated locating bearing (such as a deep-groove ball bearing, four-point contact bearing, or opposed locating pair) at the opposite housing position.
How does NU228EM prevent thermal binding in long electric-motor or fan shafts?
As a rotor or fan shaft warms up during service, its length increases relative to the stationary frame. Inside NU228EM, the roller set slides smoothly across the smooth inner-ring raceway in either direction within permissible axial displacement limits, neutralizing thermal axial stress without requiring a loose outer-ring housing fit.
When should engineers step up from NU228EM to NU2228EM or NU328EM?
If a 140 mm floating shaft experiences higher radial loads than 395 kN can comfortably support, NU2228EM keeps the same 250 mm OD while widening to 68 mm to raise Cr to 550 kN (15.9 kg). When housing diameter can expand to 300 mm, NU328EM (62 mm wide, 23.7 kg) increases Cr further to 665 kN.
What information helps ZQM confirm an NU228EM MRO replacement quickly?
Provide the existing stamped designation (including clearance code such as CN or C3), machine position, operating speed/lubrication method, and required quantity. Note that any post-mount feeler check on radial cylindrical roller units confirms mounted residual radial clearance rather than final hot operating clearance.








