Harbor tugs, offshore supply vessels, and ice-class workboats slam from full ahead to crash astern in seconds while steel hull girders flex over heavy swells. Built around a 120 × 250 × 78 mm heavy cross-section weighing 17.1 kg, the ZQM 29424 spherical roller thrust bearing anchors marine azimuth thruster lower gearboxes and rudder-stock carriers with 1,160 kN dynamic axial capacity (Ca), 3,400 kN static shock rating (C0a), and 1,300 rpm oil speed capability (900 rpm grease).
29424 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 120 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 250 mm |
| Boundary Dimensions & Weight | Overall height (H) | 78 mm |
| Boundary Dimensions & Weight | Inner-ring width (B) | 50.5 mm |
| Boundary Dimensions & Weight | Outer-ring width (C) | 37 mm |
| Boundary Dimensions & Weight | Inner-ring rib / raceway diameter (d1) | 222 mm |
| Boundary Dimensions & Weight | Outer-ring rib / raceway diameter (D1) | 172 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 17.1 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Ca) | 1160 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Coa) | 3400 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 900 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1300 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 180 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 205 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 4 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 3 mm |
| Abutment & Fillet Dimensions | Axial offset (S) | 74 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Propulsion & Hull-Flex Engineering Features of the 29424
Marine drivelines operate far from dry dock; bearing geometry must survive reversing hydrodynamic pressure, propeller blade impact, and elastic hull distortion simultaneously:
- 3,400 kN Static Slam Defense: Massive 294-series rollers and deep-hardened washers (shaft ring B = 50.5 mm, housing ring C = 37 mm) guard raceways against brinelling when propellers strike submerged timber, ice floes, or grounding bars.
- Hull-Deflection Compensation at S = 74 mm: Elastic hogging and sagging of welded thruster struts tilt shaft centerlines continuously; the spherical housing raceway pivots freely about S = 74 mm without pinching roller ends.
- Bidirectional Reversing Readiness: Installed in opposed pairs along the propeller shaft, one 29424 locks ahead thrust while its partner arrests astern pull—carrying lateral blade forces up to Fr ≤ 0.55 · Fa at the same time.
- Submerged L-Drive Oil Compatibility: Running inside pressurized mineral or environmentally acceptable synthetic marine gear oil (EAL) keeps frictional torque predictable across the full 0–1,300 rpm propulsion speed band.
Marine OEM Cross-Reference Guide for 29424 (ISO 104)
| Supplier | Designation | d (mm) | D (mm) | H (mm) | Marine Retrofit Context |
|---|---|---|---|---|---|
| ZQM | 29424 | 120 | 250 | 78 | Catalog ISO 294 baseline; cage confirmed on order |
| SKF | 29424 E | 120 | 250 | 78 | Stamped steel cage Explorer rating |
| FAG / Schaeffler | 29424-E1 | 120 | 250 | 78 | Optimized high-load marine thruster spec |
| NSK | 29424 / 29424M | 120 | 250 | 78 | Machined brass cage option for shock duty |
| NTN / Timken | 29424 / 29424EM | 120 | 250 | 78 | Heavy-series propulsion and steering equivalents |
Marine compliance note: The cross-list above matches ISO 104 nominal boundary dimensions (120 × 250 × 78 mm) strictly for reference. Classification-society survey requirements, cage alloy, and paired axial clearance vary by vessel builder—always validate drawings and inspection documentation prior to dry-dock installation.
Dry-Dock Mounting, Preload & Seawater Exclusion Protocol
- Machine Robust Stress-Relieved Shoulders: Provide shaft abutment da ≥ 180 mm (matching d1 = 222 mm shaft washer OD) and housing lip Da ≤ 205 mm (housing washer bore D1 = 172 mm). Restrict shaft and housing fillet radii to ra ≤ 3 mm within the generous 4 mm minimum chamfer.
- Prevent Unloaded-Partner Skidding in Paired Pods: During sustained ahead steaming, the opposing astern 29424 sees zero hydrodynamic thrust. Apply calibrated spring preload across the opposed housing washers so the idle partner retains minimum axial load and never smears its raceway.
- Defend Against Saltwater Ingress: Even 0.1% seawater contamination halves rolling fatigue life via hydrogen embrittlement. Pair the thruster pod with positive-head gravity oil tanks (0.2–0.3 bar above external draft pressure), triple-lip rotary shaft seals, and water-coalescing offline bypass filtration.
- Verify Housing Washer Radial Clearance: Ensure the 250 mm outer diameter of the housing washer seats with proper radial freedom when external radial roller bearings carry primary bevel-gear loads, preserving full spherical alignment.
Coordinating an urgent dry-dock thruster overhaul or rudder-carrier spares package? Contact our marine bearing engineering desk with shaft diameter, propulsion power, and required cage execution for rapid delivery planning.
Marine Azimuth Thruster & Rudder Stock 29424 FAQ
Related Selection & Comparison: Compare marine and mill thrust options alongside the 150 mm 29430 thrust roller bearing, decode ISO 104 E/EM suffixes in our Bearing Suffix Decoder, or explore Industrial Gearboxes.
Why do marine azimuth thrusters pair two 29424 bearings back-to-back?
Each 29424 supports axial thrust in a single direction only. Mounting an opposed pair lets one bearing absorb full-ahead bollard pull while the other arrests sudden crash-astern braking forces, with calibrated preload keeping both roller sets stabilized.
How does the 29424 cope with hull deformation in rough sea states?
The housing washer’s spherical raceway pivots around a center point 74 mm from the shaft washer back face, letting the 120 mm propulsion shaft flex relative to the thruster housing without overloading the ends of the rollers.
Can the 29424 be grease-lubricated on a slow-turning rudder stock?
Yes—oscillating rudder-stock carriers operate far below the 900 rpm grease limit and commonly use water-resistant marine EP grease with regular purging. Continuous-rotation propulsion shafts, however, must run in circulating or submerged marine gear oil (rated up to 1,300 rpm).
Why is the 4 mm chamfer important on a 120 mm propulsion shaft?
Propeller shafts transmit extreme torsional shock during emergency reversals. The 4 mm minimum bearing chamfer allows designers to machine a generous ra = 3 mm shaft shoulder fillet that minimizes torsional stress concentration while still seating the 50.5 mm shaft washer flat.



