51216 Thrust Ball Bearing 80 × 115 × 28 mm

ISO 104 Series 12 single-direction flat-seat 51216 thrust ball bearing (80 × 115 × 28 mm, total height H = 28 mm) engineered for sustained unidirectional screw-nut compression inside heavy trapezoidal screw-jacks and industrial lifting platforms (Fr = 0). Axial ratings Ca/C0a confirmed on factory drawing.

The 51216 thrust ball bearing (80 × 115 × 28 mm, ISO 104 Dimension Series 12) strengthens the 80 mm bore envelope dramatically over extra-light 51116 (80 × 105 × 19 mm), expanding outer diameter to 115 mm and total height (H) to 28 mm. Built for heavy mechanical trapezoidal screw-jacks, synchronized stage-lift columns, and industrial mold-clamping presses, it carries continuous unidirectional vertical compression (Fr = 0) cleanly beneath rotating worm-wheel drive nuts.

ISO 104 Parameter Symbol 51216 Nominal Screw-Jack Design Notes
Shaft Washer Bore d 80 mm Fits 80 mm drive-sleeve / screw hub
Housing Washer OD D 115 mm 10 mm wider OD than thin 51116
Total Assembled Height H 28 mm Sturdier Series 12 axial cross-section
Load Axis Envelope Pure Axial Only Fr = 0 Unidirectional No radial support; flat-seat zero tilt
Separable Design 3-Piece Flat Seat Housing Bore D1 > 80 mm Never swap shaft & housing washers
Axial Capacities & Cage Ca / C0a / Cage Factory Drawing Verified Steel vs brass cage & Ca/C0a confirmed at quote

51216 Sustained Compression & Housing-Seat Flatness in Screw-Jacks

Trapezoidal and acme-thread worm-gear screw-jacks support rail-car maintenance lifts, ladle-transfer platforms, and steel-mill pass-line adjusters where tons of dead weight press relentlessly downward onto the rotating bronze drive sleeve. While worm-gear efficiency consumes a portion of motor torque, poor thrust support multiplies input power demand and causes chatter during slow lowering. Upgrading from 51116 to the beefier Series 12 51216 (115 mm OD, 28 mm height) inserts larger rolling balls capable of sustaining heavy compressive cycles day after day.

Flat-seat geometry demands strict machining discipline inside the screw-jack gearbox casing: the counterbore floor beneath the housing washer must be ground or precision-faced flat and dead-square to the screw axis because the 51216 has zero misalignment tolerance. Likewise, lateral wind loads or eccentric platform overturning moments must be absorbed entirely by external linear guide posts and gearbox radial bearings so the thrust pocket experiences strictly Fr = 0. Because centrifugal skidding restricts thrust ball bearings to low-to-moderate speeds, never apply 51216 on high-rpm servo spindles. Exact Ca/C0a ratings, cage alloy (pressed steel or machined brass), and tolerance grades are finalized on our factory engineering print at quotation.

51216 Equivalent Codes & Legacy 8216 Cross-Reference

Lifting-system builders and MRO teams servicing mechanical jack gearboxes routinely match ISO 104 Series 12 numbers against legacy Chinese code 8216:

Brand / Standard ISO 104 Base Code Jack Gearbox Checkpoints
ZQM Bearings 51216 Factory drawing confirms Ca/C0a, D1 bore & cage
SKF 51216 Flat-seat Series 12; verify pressed steel vs brass cage
FAG / Schaeffler 51216 Check static seating factor under parked full load
NSK / NTN / KOYO 51216 Confirm compatibility with worm-gearbox splash oil
Legacy GB Code 8216 Former Chinese lifting-jack blueprint designation

Interchange Boundary: Cross-listed designations verify ISO 104 exterior envelope identity (80 × 115 × 28 mm) strictly. Raceway metallurgy, cage design, and dynamic/static axial load capacities Ca/C0a differ across brands and must be validated before replacing safety-critical lifting components.

Gearbox Lubrication, Washer Fitment & Push-Pull Arrangements

Inside enclosed worm-gear screw-jacks operating across heavy manufacturing and steel-handling platforms, synthetic worm-gear oil or semifluid EP grease lubricates both the bronze wheel and the 51216 thrust raceways simultaneously. Verify oil passages feed the lower bearing pocket cleanly so horizontal mounting never starves the balls.

During gearbox assembly, confirm washer orientation visually and with calipers: the tight 80 mm shaft washer seats against the rotating worm-wheel hub, while the larger-bore housing washer (D1 > 80 mm) nests flat inside the cast housing bore so the rotating hub never drags on it. Maintain light axial preload during unloaded return strokes to prevent ball skidding. Whenever a lifting jack alternates between compressive pushing and tensile pulling loads, mount a matched opposed pair of 51216 bearings (one on each face of the worm-wheel flange) or engineer around a double-direction 522/523/524 thrust unit.

Ordering 51216 Bearings for Screw-Jack OEMs & Lift Maintenance

Provide your jack tonnage capacity, compression-only vs push-pull opposed layout, gearbox lubricant type, cage preference (steel or solid brass), and order quantity. We send back a verified factory drawing confirming axial Ca/C0a ratings and housing bore D1 prior to manufacturing.

Request 51216 Screw-Jack Specs & Quote

51216 Technical FAQ for Mechanical Screw-Jacks & Lifts

Related Selection & Comparison: Compare extra-light 80 mm height via 51116 (19 mm) or 100 mm mixer shafts via 51220, and review all ISO 104 options in Thrust Ball Bearings.

How does 51216 compare against 51116 on an 80 mm jack sleeve?

Both fit an 80 mm diameter hub, but Series 12 51216 increases OD from 105 mm to 115 mm and total height H from 19 mm to 28 mm, accommodating much larger balls and heavier washers for sustained lifting compression.

Why is housing-seat flatness so crucial beneath a 51216 screw-jack bearing?

Flat-seat ISO 104 thrust ball bearings tolerate zero angular misalignment. Even a slight machining taper on the gearbox pocket shifts full platform tonnage onto a small arc of balls, causing premature raceway spalling.

Can one 51216 support a screw-jack that both lifts (compression) and pulls down (tension)?

No—a single 51216 carries axial force in one direction only. Push-pull screw-jacks place two 51216 bearings on opposite sides of the worm-gear hub or use a double-direction 522/523/524 thrust ball bearing.

How do technicians verify shaft vs housing washer placement in a 51216?

Check the bore: the 80 mm shaft washer fits snugly onto the rotating drive sleeve, whereas the housing washer has a larger bore (D1 > 80 mm) to clear the sleeve cleanly inside the stationary gearbox pocket.

Scroll to Top