51116 Thrust Ball Bearing 80 × 105 × 19 mm

Thin-section ISO 104 Series 11 single-direction flat-seat 51116 thrust ball bearing (80 × 105 × 19 mm, total height H = 19 mm) built around hollow 80 mm columns on beverage capping carousels and rotary packaging turrets. Pure unidirectional axial load (Fr = 0); Ca/C0a confirmed on factory drawing.

The 51116 thrust ball bearing (80 × 105 × 19 mm, ISO 104 Dimension Series 11) wraps a remarkably slender 12.5 mm radial wall and 19 mm total height (H) around an 80 mm hollow center column. Designed for bottling-line beverage capping carousels, rotary labeling turrets, and blister-packaging index stars, it supports pure downward column weight (Fr = 0) while leaving the central 80 mm bore wide open for pneumatic manifolds, slip rings, and CIP washdown tubes.

ISO 104 Field Symbol 51116 Nominal Packaging Turret Notes
Shaft Washer Bore d 80 mm Fits 80 mm hollow turret column
Housing Washer OD D 105 mm Slim 12.5 mm radial section width
Total Height H 19 mm Low-profile vertical column stack
Load Restriction Pure Axial Only Fr = 0 Unidirectional No radial capacity; zero tilt tolerance
Separable Washers Shaft vs Housing D1 > 80 mm on Housing Never invert shaft and housing rings
Axial Ratings & Cage Ca / C0a / Cage Factory Drawing Confirmed Verified per speed, grease & cage at quote

51116 Hollow-Column Geometry for Rotary Bottling Turrets

Modern rotary bottle fillers, screw-cappers, and slewing cartoners route compressed air, vacuum lines, and servo encoder harnesses straight down a hollow 80 mm stainless pedestal. That wide hollow quill rules out small-bore bearings, yet tight star-wheel spacing outside the column forbids oversized outer diameters. The 51116 solves this geometric squeeze cleanly: 80 mm inside, 105 mm outside, and just 19 mm tall.

Although high-throughput bottling lines produce hundreds of bottles per minute, the main turret column itself turns at moderate rotational rpm—well inside a thrust ball bearing’s safe kinematic window provided two engineering checks are respected. First, dead turret weight must consistently exceed the minimum axial load threshold so centrifugal action never causes ball skidding during empty-carousel dry runs. Second, radial gear-mesh forces driving the turret ring gear must be isolated completely onto separate radial column bearings because the flat-seat 51116 carries strictly zero radial load (Fr = 0) and zero misalignment. Axial capacities (Ca / C0a), limiting speed, and steel vs brass cage specifications are confirmed on our formal drawing at quotation.

51116 Brand Cross-Reference & Legacy 8116 Identification

Food-and-beverage plant engineers maintaining Italian, German, and Chinese rotary packaging lines regularly reference these ISO 104 Series 11 codes (legacy GB code 8116):

Brand / Standard ISO 104 Designation Packaging Line Notes
ZQM Bearings 51116 Factory drawing confirms D1 bore, cage & Ca/C0a
SKF 51116 Standard flat-seat Series 11; verify steel vs brass cage
FAG / Schaeffler 51116 Check food-grade grease compatibility on open assembly
NSK / NTN / KOYO 51116 Confirm axial face flatness & tolerance class
Legacy GB Code 8116 Older Chinese packaging machinery blueprints

Interchange Boundary: Matching 51116 across brands verifies ISO 104 exterior dimensions (80 × 105 × 19 mm) alone. Retainer construction, material cleanliness, and axial load ratings Ca/C0a vary by maker and must be checked against machine blueprints prior to substitution.

Washdown Hygiene, Washer Orientation & Flat-Seat Alignment

Inside beverage bottling halls and automated industrial packaging lines, caustic foam sanitation destroys open steel thrust bearings if lip seals or labyrinth shields leak. Because the 51116 separates into three loose pieces during overhaul, technicians can flush old H1 food-grade grease thoroughly and inspect both ground ball tracks visually.

On reassembly, verify washer bores carefully: seat the tight 80 mm shaft washer squarely onto the rotating turret collar and drop the larger-bore housing washer (D1 > 80 mm) into the flat stationary pedestal base—never swap them, or the stationary ring will seize against the column. Machine both seating shoulders strictly perpendicular to the column centerline; if turret lifters ever pull upward in addition to downward weight, transition to a 522/523/524 double-direction thrust bearing or QJ unit.

Ordering 51116 Bearings for Packaging OEMs & Bottling MRO

Send us your turret column operating speed, washdown environment, preferred cage type (pressed steel or machined brass), tolerance grade, and annual or single-batch quantity. We issue a verified factory drawing detailing housing clearance bore D1 and axial Ca/C0a ratings before production.

Request 51116 Packaging Turret Drawing & Quote

51116 Technical Questions for Rotary Packaging Lines

Related Selection & Comparison: Need higher axial shock capacity on an 80 mm shaft? Compare Series 12 51216 (115 × 28 mm), check our Quality Control Lab flatness verification, or browse Thrust Ball Bearings.

Why is 51116 popular on hollow-shaft rotary capping carousels?

Its 80 × 105 × 19 mm ISO 104 Series 11 geometry provides an 80 mm central passage for air and electrical utilities while occupying only a 12.5 mm radial wall and 19 mm vertical stack.

What happens if a dry-run capping turret rotates with too little downward weight on the 51116?

Without adequate minimum axial preload, centrifugal force lifts the rolling balls against the outer groove wall, causing ball skidding, cage wear, and raceway smearing.

Can 51116 resist the radial tooth load from a turret spur drive gear?

No. A 51116 flat-seat thrust ball bearing supports strictly pure axial loads (Fr = 0). Radial gear-mesh separation forces must be supported by dedicated radial bearings along the column.

How do maintenance crews avoid reversing the 51116 washers during overhaul?

Check the bore diameter before installation: the shaft washer fits the 80 mm rotating shaft tightly, while the housing washer has a noticeably larger clearance bore (D1 > 80 mm) to clear the spinning column.

Scroll to Top