Rolling Mill Bearings: FCD vs FCDP Four-Row Cylindrical and 322/323

Rolling mill work rolls and backup rolls operate under extreme separating forces, shock loads during strip entry, and tight chock envelope limits. Selecting between a four-row cylindrical roller bearing (FCD / FCDP / FC) and a heavy-section tapered roller bearing (322 / 323 series) depends on how radial and axial loads are separated inside the roll chock.

Rolling mill bearing architecture comparing FCD/FCDP four-row cylindrical roller bearings with 322/323 tapered roller bearings
Comparison of four-row cylindrical work-roll bearings (FCD / FCDP) and heavy tapered roller bearings (322 / 323) in rolling mill chocks.

FCD vs FCDP Four-Row Cylindrical Roller Bearings

Four-row cylindrical roller bearings maximize radial load capacity within a compact cross-section while allowing the roll neck to float axially inside the chock during thermal expansion. Comparing two 280 × 390 × 275 mm rolling mill units from the ZQM catalog:

  • FCDP5678275/YA3: 280 × 390 × 275 mm, dynamic load rating Cr 2,720 kN, static load rating C0r 6,130 kN, mass 105 kg. The FCDP designation uses a pin-type (pierced roller) cage architecture that allows larger or more densely packed rollers for higher dynamic capacity and strong resistance to sudden impact loads.
  • FCD5678275 (SKF BC4-0100 / 314719C, FAG 527104 nominal-envelope reference) & FC5678275/YA3: 280 × 390 × 275 mm four-row cylindrical roller unit (FC5678275/YA3 delivers Cr 2,260 kN and C0r 6,940 kN, 105 kg) with solid machined brass cage suited for high-speed continuous strip and wire rod stands where cage guidance stability is critical. Cross-reference for identification only. Verify interchangeability with engineering drawings.

Chock Note: Both FCD and FCDP carry pure radial load only. They must be paired with an external axial locating unit—commonly a four-point contact ball bearing or a matched tapered roller pair—to restrain axial roll shifting.

322 vs 323 Tapered Roller Bearings for Combined Loads

Where roll stands, mill pinions, or intermediate gearboxes experience simultaneous radial and axial thrust loads in a smaller envelope, single-row or paired tapered roller units provide rigid axial positioning:

Parameter 32224 32324
Dimensions (d × D × T) 120 × 215 × 61.5 mm 120 × 260 × 90.5 mm
Dynamic Load Rating (Cr) 440 kN 770 kN
Static Load Rating (C0r) 635 kN 1,060 kN
Mass 9.0 kg 21.8 kg
Primary Rolling Duty Medium-heavy radial + axial gear & roll-neck thrust duty Extreme shock radial + heavy axial thrust duty

Worked Chock Assembly: Floating & Locating Units

In a typical work-roll chock layout, engineers separate vertical separating forces from axial strip-guiding thrust so neither unit binds as the roll heats up during rolling:

  • Floating Cylinder Side + Four-Point Contact Locating Unit: A 280 mm roll neck carrying an FCDP5678275/YA3 or FCD5678275 (280 × 390 × 275 mm) for pure radial duty can be axially located by a dedicated four-point contact ball unit such as 116756 / QJF1058MB (280 × 419.5 × 65 mm, Cr 553 kN, C0r 1,060 kN, 33.6 kg, grease 950 / oil 1,400 rpm). Critically, 116756 / QJF1058MB uses a special 419.5 mm outside diameter rather than a standard 420 mm QJ series outer diameter—chock housing bores and radial clearance around the locating ring must be verified on the engineering drawing to avoid housing mismatch.
  • Back-to-Back 32224 / 32324 Thrust Arrangements: On pinion stands, auxiliary roll necks, and lighter intermediate stands where separate radial and thrust housings are impractical, paired 32224 or 32324 tapered roller sets arranged back-to-back handle bidirectional axial thrust alongside radial load. Moving from 32224 (215 mm OD) to 32324 (260 mm OD) increases dynamic capacity from 440 kN to 770 kN for high shock passes when chock envelope permits.

Pre-Order Verification & Lubrication Inspection

Before ordering replacement rolling mill bearings or closing a rebuilt chock, complete four shop-floor checks:

  1. Lubrication Groove & Oil-Hole Alignment (YA3 / W33): Inspect the outer-ring circumferential oil groove and radial oil feed holes (such as YA3 or W33 lubrication features) and confirm they align directly with the chock housing oil ports and oil-air nozzle passages.
  2. Inner Ring & Roll-Neck Interference: Check roll-neck journal roundness, shoulder squareness, and inner ring bore interference. Verify whether inner rings are matched to a specific outer-ring/roller assembly or supplied as interchangeable spares before mixing roll-neck sleeves across stands.
  3. Clearance & Endplay Setting: Confirm internal radial clearance (commonly C3 or C4 for hot mills) on the cylindrical unit and verify axial endplay on the locating unit using a dial indicator after chock cover bolting.
  4. Chock Envelope & Cross-Reference Drawings: Verify exact chock width (275 mm on the 5678275 series) and outer diameter tolerances against your mill chock engineering drawing before finalizing purchase orders.

Frequently Asked Questions

Can FCD and FCDP four-row cylindrical roller bearings carry axial thrust loads on their own?

No. Four-row cylindrical roller units such as FCD5678275 and FCDP5678275/YA3 carry pure radial load only and allow axial float on the raceway. A separate locating bearing—such as a four-point contact ball unit or paired tapered roller set—is required to control axial roll position.

Why must housing bores be checked when pairing 116756 (QJF1058MB) with a 280 mm roll-neck bearing?

Although 116756 / QJF1058MB shares the 280 mm bore of 5678275-series roll-neck bearings, its outside diameter is a special 419.5 mm rather than a standard 420 mm QJ outer diameter. Confirming the chock housing bore and fit clearance on the drawing prevents improper seating or outer-ring pinch.

How do engineers decide between 322 and 323 tapered roller bearings in mill drives and chocks?

On the same 120 mm bore, 32224 (120 × 215 × 61.5 mm, Cr 440 kN) suits compact chocks and medium-heavy gearboxes, while 32324 (120 × 260 × 90.5 mm, Cr 770 kN) provides steeper load capacity and shock reserve when heavier axial thrust and radial impacts govern service life.

Sourcing Rolling Mill Bearings for Your Stand?

Share your bearing code (FCD, FCDP, 322/323, or roll neck dimensions), lubrication method (oil-air or grease), and target clearance. ZQM Bearings provides factory-direct engineering verification and quotation.

Request Mill Bearing Quote

Scroll to Top