294 SERIES · SPHERICAL ROLLER THRUST BEARING
29424 Spherical Roller Thrust Bearing Dimensions & Specifications
29424 spherical roller thrust bearing: 120 mm bore (d), 250 mm outside diameter (D), 78 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 120 mm |
|---|---|
| Outside diameter D | 250 mm |
| Total height H | 78 mm |
| Housing washer height C | 37 mm |
| Mass | 17.1 kg |
| Catalogue dynamic load Ca | 1160 kN |
| Catalogue static load Coa | 3400 kN |
| Grease-lubricated speed | 900 rpm |
| Oil-lubricated speed | 1300 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 205 mm |
|---|---|
| Abutment dimension da | 180 mm |
| Minimum chamfer r12 | 4 mm |
| Diameter D1 | 172 mm |
| Diameter d1 | 222 mm |
| Maximum fillet ra | 3 mm |
| Offset S | 74 mm |
| Shaft washer height B | 50.5 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 9039424 | ZQM Catalogue P.252 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 29424?
The 29424 catalogue lists da min = 180 mm; Da max = 205 mm; ra max = 3 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29424?
The listed values for 29424 are grease: 900 rpm; oil: 1300 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29424?
The catalogue reference mass for 29424 is 17.1 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29424 spherical roller thrust bearing?
29424 (120 × 250 × 78 mm, total height H = 78 mm and housing washer height C = 37 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29424
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

