Procurement and maintenance engineers frequently receive MRO bills of materials stamped with SKF, FAG, NSK, or NTN designations and need a reliable bearing cross reference ISO suffix guide before issuing an RFQ. While external boundary dimensions follow ISO 15 nominal envelopes, internal cage architecture, lubrication grooves, bore taper angles, and legacy non-standard outer diameters vary substantially across brands.

Why Nominal ISO Size Does Not Equal Drop-In Interchangeability
Every credible bearing cross reference ISO suffix guide separates identification equivalence (shared d × D × B envelope) from functional interchangeability (matching load, speed, thermal behavior, and housing clearance). Two assemblies carrying the same four- or five-digit base number can behave very differently on the shop floor:
CAandMBmachined brass cages withstand severe vibration and shock better than stamped steelCC/ECJ.- Internal roller diameter and under-roller envelope
Fwdiffer across brands—never swap separable inner rings across manufacturers.
240and241spherical series use 1:30 (K30) tapers ONLY—never mix with 1:12 (K) sleeves.- Legacy four-point unit 116756 / QJF1058MB measures 280 × 419.5 × 65 mm, not standard 420 mm QJ1056!
Global Brand Suffix Matrix: SKF, FAG, NSK, NTN vs ZQM
The 3-column table below maps major brand suffix conventions across spherical roller, cylindrical roller, lubrication, bore taper, and radial internal clearance families. Always pair this bearing cross reference ISO suffix guide with verified ZQM product sheets such as 23148 CA/W33, 23056 CA/W33, and NJ226EM.
| Design Feature & ZQM Suffix | SKF / FAG Suffix Equivalents | NSK / NTN Reference & Verification Note |
|---|---|---|
| Spherical Machined Brass Cage (CA / MB) | SKF: CA / CAC · FAG: E1-XL-MB1 / M | NSK: CAM / CAME4 · NTN: EMD1 / B — verify symmetrical vs guide-ring retention on vibrating screens |
| Spherical Stamped Steel Cage (CC / E) | SKF: CC / E · FAG: E1-XL (sheet steel) | NSK: EA · NTN: EA — higher limiting speed in clean gearboxes; compare against 23148 CA/W33 (Cr 1,790 kN) |
| Outer-Ring Groove & 3 Oil Holes (W33) | SKF: W33 · FAG: S | NSK: E4 · NTN: D1 — confirm oil-hole count and housing port alignment before drop-in fit |
| Cylindrical Reinforced Brass Cage (EM / M) | SKF: ECM / ECML · FAG: E-XL-M1 | NSK: EM · NTN: EG1 — straight cylindrical bore ONLY (e.g., NJ226EM, 130 × 230 × 40 mm, Fw 153.5 mm) |
| Tapered Bore 1:12 (K) vs 1:30 (K30) | SKF/FAG: K (222/223/230/231/232) · K30 (240/241) | NSK/NTN: K vs K30 — strictly 1:30 K30 on 240 series and 241 series |
| Radial Internal Clearance (C0 / C3 / C4) | SKF/FAG: CN (omitted) / C3 / C4 | NSK/NTN: CN / C3 / C4 — specify C3/C4 for heavy shaft interference or high thermal differential |
Engineering Interchange Disclaimer: Cross-reference for identification only. Verify interchangeability with engineering drawings. Listed suffixes share nominal ISO functional categories only; exact roller counts, shoulder diameters, and dynamic capacities vary by manufacturer.
Three Real Cross-Reference Pitfalls Caught on Shop Floors
Before releasing a cross-referenced purchase order, check three pitfalls that frequently trigger assembly rejections:
- Separable Cylindrical Inner Rings (Fw Mismatch): On NJ226EM (130 × 230 × 40 mm, Cr 290 kN, Cor 410 kN, 7.38 kg, 2,200/2,800 rpm), ZQM specifies
Fw = 153.5 mm, whileDb,da, andEwremain uncatalogued (contact us for specifications). Because reinforcedEdesigns vary slightly inFwbetween legacy and modern series, always replace the inner ring and outer-ring assembly as a matched set rather than mixing an old SKF or FAG inner ring with a new outer ring. - 419.5 mm Non-Standard OD on 116756 / QJF1058MB: Many buyers mistake old code
116756for a standard 420 mmQJ1056four-point contact unit. Verified ZQM catalog records (QJF1058MB) confirm a special 280 × 419.5 × 65 mm envelope (Cr 553 kN, Cor 1,060 kN, 33.6 kg, 950/1,400 rpm, a = 245 mm)—a 0.5 mm OD difference that demands housing drawing confirmation. - 1:12 K vs 1:30 K30 Taper Mix-Ups on 240/241: While 23056 CA/W33 (280 × 420 × 106 mm, 50.5 kg) and 23148 CA/W33 (240 × 400 × 128 mm, 66.9 kg) take a standard 1:12
Ktaper when ordered tapered, wide-section 240 and 241 series take 1:30K30exclusively.
Pre-Order Engineering Checklist Before Converting an RFQ
Before finalizing any bill of materials translated through this bearing cross reference ISO suffix guide, procurement and maintenance teams should confirm four engineering checkpoints so factory deliveries match housing tolerances and lubrication systems:
| Verification Step | Required Drawing / Field Evidence | Why It Prevents Field Rejection |
|---|---|---|
| 1. Bore Type & Sleeve Match | Confirm straight bore vs 1:12 K vs 1:30 K30 taper and adapter/withdrawal sleeve series | Mismatched cone angles split inner rings during hydraulic nut drive-up |
| 2. Cage & Vibration Profile | Verify solid brass CA/MB/M vs stamped steel CC/E against shock and speed rpm | Prevents pocket cracking on crushers, screens, and rolling-mill pinions |
| 3. Clearance & Thermal ΔT | Specify C0, C3, or C4 radial internal clearance plus shaft/housing ISO 286 fits | Prevents zero-clearance thermal pinch on heated rolls and interference fits |
| 4. Abutment & Port Alignment | Check da, Da, r1,2, ra limits and W33/S/E4 oil-groove port alignment | Guarantees chamfer clearance and pressurized oil delivery across both rows |
Frequently Asked Questions
Does this bearing cross reference ISO suffix guide guarantee direct drop-in replacement across SKF, FAG, NSK, and NTN?
No. Cross-reference for identification only. Verify interchangeability with engineering drawings. Shared nominal ISO boundary dimensions do not guarantee identical cage guidance, Fw under-roller diameters, shoulder abutments, or oil-hole alignment.
Which suffixes indicate outer-ring lubrication grooves and holes across brands?
ZQM and SKF use W33, FAG uses S, NSK uses E4, and NTN uses D1 to denote a circumferential outer-ring lubrication groove with three radial feed holes. Always verify housing oil-port alignment during overhaul.
Why should buyers never mix separate cylindrical inner and outer rings from different manufacturers?
Reinforced cylindrical series such as NJ226EM can differ slightly in roller envelope diameter Fw and internal radial clearance tolerances across makers. Install matched complete units to prevent edge loading and skidding.
Related ZQM Engineering Tools & Catalog Lookup
- Interactive Bearing Suffix Decoder — translate SKF, FAG, NSK, NTN, and ZQM cage, groove (
W33 / S / E4 / D1), and clearance suffixes side by side. - 1:12 K vs 1:30 K30 Tapered Bore Calculator — verify radial clearance reduction and axial drive-up before cross-referencing tapered-bore assemblies.
- ZQM 6,300+ Model Online Bearing Catalog — verify nominal ISO boundary dimensions (
d × D × B) and legacy designations such asQJF1058MB (116756).
Need Engineering Verification on a Brand Cross-Reference?
Share your existing OEM part number, equipment model, or housing drawing. ZQM engineers will verify exact dimensions, suffix behavior, and radial clearance before quotation.

