294 SERIES · SPHERICAL ROLLER THRUST BEARING
29476 Spherical Roller Thrust Bearing Dimensions & Specifications
29476 spherical roller thrust bearing: 380 mm bore (d), 670 mm outside diameter (D), 175 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 380 mm |
|---|---|
| Outside diameter D | 670 mm |
| Total height H | 175 mm |
| Housing washer height C | 87.5 mm |
| Mass | 260 kg |
| Catalogue dynamic load Ca | 5800 kN |
| Catalogue static load Coa | 24000 kN |
| Oil-lubricated speed | 480 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 575 mm |
|---|---|
| Abutment dimension da | 510 mm |
| Minimum chamfer r12 | 7.5 mm |
| Diameter D1 | 494 mm |
| Diameter d1 | 610 mm |
| Maximum fillet ra | 6 mm |
| Offset S | 222 mm |
| Shaft washer height B | 120 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29476?
The 29476 catalogue lists da min = 510 mm; Da max = 575 mm; ra max = 6 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29476?
The listed values for 29476 are oil: 480 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29476?
The catalogue reference mass for 29476 is 260 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29476 spherical roller thrust bearing?
29476 (380 × 670 × 175 mm, total height H = 175 mm and housing washer height C = 87.5 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 61876 | Deep Groove Ball Bearing | 380 × 480 × 46 mm |
| NUP2876Q1 | Cylindrical Roller Bearing | 380 × 480 × 60 mm |
Compare alternative series sharing the same 380 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29476
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

