2310 Self-Aligning Ball Bearing 50 × 110 × 40 mm

Heavy wide-series 2310 self-aligning ball bearing (50 × 110 × 40 mm, ISO 15 Series 23), built for steep overhang radial loads on industrial dewatering pump pedestals and brick-making mixer shafts. Supplied straight 2310, sealed -2RS, or 1:12 tapered 2310K with H2310 sleeve; verify ball side-protrusion.

The 2310 self-aligning ball bearing (50 × 110 × 40 mm, ISO 15 Dimension Series 23) represents the widest, heaviest-section double-row ball execution available on a 50 mm shaft—delivering a massive 40 mm axial footprint compared with 27 mm on the 1310. Tailored for overhung industrial dewatering pump pedestals and clay pug-mill or brick-making extrusion mixer shafts, it is offered in cylindrical 2310, contact-sealed 2310-2RS, or 1:12 tapered 2310K paired with an H2310 sleeve for 45 mm shafting.

ISO 15 Specification Symbol 2310 Nominal Series 23 Engineering Remarks
Bore Diameter d 50 mm Straight cylindrical journal
Outside Diameter D 110 mm Matches 1310 housing bore OD
Extra-Wide Width B 40 mm 13 mm wider than 1310; verify ball protrusion
Tapered & Sealed Variants 2310K / -2RS 1:12 Taper / Dual Seals 2310K uses long H2310 sleeve (45 mm shaft)
Internal Geometry Double-Row Ball Sphered Outer Ring Heavy ball set; point contact (p = 3)
Load Ratings & Cage Cr / C0r / Cage Factory Drawing Verified Steel, brass, or polymer confirmed per quote

2310 Overhang Rigidity & Mandatory Side-Protrusion Check

Horizontal dewatering pump frames and clay-tempering mixer troughs exert substantial cantilevered radial bending loads where heavy impellers or twin-paddle shafts overhang their bearing pedestals. Stretching the bearing width to 40 mm inside the 50 × 110 mm Series 23 envelope spreads the two heavy ball rows far apart, resisting shaft tilt while retaining automatic spherical self-alignment (around 2.5°–3° open) when cast pedestals shift on wet plant floors.

Critical Assembly Warning — Ball Protrusion: Because the 2310 houses large-diameter balls inside a compact sphered outer ring, verify axial ball side-protrusion against our factory drawing before bolting on seal carriers, spacer collars, or pump-frame retaining plates—contact between stationary hardware and proud balls causes instantaneous seizure. Also evaluate thrust and impact severity carefully: while 2310 offers the highest radial stamina among 50 mm self-aligning ball bearings, heavy clay extrusion augers generating sustained axial push or quarry rock shock should be evaluated for 22310 spherical roller bearings or dedicated thrust stages.

2310 Brand Cross-Reference & Legacy 1610 Identification

Maintenance supervisors supporting dewatering skids and ceramic/brick plants often cross-reference these ISO 15 Series 23 designations (legacy Chinese code 1610):

Manufacturer / Standard Open Cylindrical 1:12 Tapered / Sealed Verification Notes
ZQM Bearings 2310 2310K / 2310-2RS Factory drawing confirms ball protrusion & cage
SKF 2310 ETN9 / 2310 2310 EKTN9 / 2310 E-2RS1TN9 2RS1 seals limit misalignment to ~1.5°
FAG / Schaeffler 2310-TVH / 2310-M 2310-K-TVH / 2310-2RS-TVH M = machined brass; TVH = polyamide (~120 °C limit)
NSK / NTN 2310 2310K / 2310LLU Confirm cage & clearance grade against OEM print
Legacy GB Code 1610 11610 Former Chinese designation for 2310 wide heavy

Scope Disclaimer: Cross-listed designations verify ISO 15 nominal envelope parity (50 × 110 × 40 mm) only. Ball overhang dimensions, seal lip geometry, cage heat resistance, and load ratings vary by producer and must be checked prior to drop-in replacement.

Slurry Splash Protection & H2310 Sleeve Fitment

Dewatering pump sumps and brickyard clay mixers in building-materials and mining facilities constantly splash abrasive mud and wet clay toward bearing end caps. Pairing open 2310 bearings with oil-bath or purge-greased pedestals behind external rotary flingers keeps grit out; where compact frames prevent purge plumbing, 2310-2RS sealed units provide a factory-greased internal barrier (observing the tighter ~1.5° alignment limit).

When mounting the 1:12 tapered 2310K onto a 45 mm plain shaft, specify the extra-long H2310 adapter sleeve—neither H210 nor H310 spans the 40 mm inner ring width properly. Confirm stamped steel or machined brass cages whenever clay-mixer frictional heat or warm pump shafts risk pushing bearings near polymer cage ceilings.

Specifying 2310 & 2310K for Pump & Brick-Plant Orders

Send our technical team your exact assembly requirements: straight 50 mm 2310 vs 1:12 tapered 2310K with H2310 sleeve, open vs -2RS sealed construction, cage material (steel, brass, or polyamide), clearance (CN or C3), and quantity. We confirm the formal drawing—including ball protrusion clearance and load ratings—before production starts.

Request 2310 Engineering Drawing & Quote

2310 Engineering FAQ for Pump Pedestals & Brick Mixers

Related Selection & Comparison: Compare standard 27 mm width on the same 50 mm bore via 1310, check H2310 1:12 sleeve matching in our Tapered Bore Tool, or browse Self-Aligning Ball Bearings.

Why is 2310 preferred over 1310 on steep-overhang dewatering pump shafts?

While both measure 50 × 110 mm in bore and OD, the 2310 widens the section from 27 mm to 40 mm, accommodating heavier double-row ball geometry and broader support spacing against cantilevered radial bending loads.

Which adapter sleeve fits the 2310K tapered bore?

The 2310K requires the extra-long metric H2310 adapter sleeve to seat properly onto a 45 mm plain shaft. Shorter H210 or H310 sleeves leave part of the 40 mm wide inner ring unsupported.

Why must housing designers verify side protrusion on a 2310?

Wide Series 23 self-aligning ball bearings can exhibit slight ball projection beyond the 40 mm nominal ring faces. Checking our factory drawing ensures adjacent slingers, spacers, and end caps clear the balls cleanly.

What legacy Chinese code corresponds to 2310?

Older brick-making machinery and pump blueprints in China identify the 50 × 110 × 40 mm 2310 as legacy code 1610 (and tapered 2310K as 11610).

Scroll to Top