29384 Spherical Roller Thrust Bearing Overview
Built for extreme axial loads on large-diameter vertical and inclined shafts, the 29384 spherical roller thrust bearing measures 420 × 650 × 140 mm (overall assembly height H = 140 mm, reference mass 175 kg). Per ZQM Bearings’ 259-page general catalogue, it provides reference axial load ratings of Ca = 3,600 kN and C0a = 16,000 kN (confirm final axial ratings on factory order drawings) with self-aligning housing washer geometry.
ISO 281 Radial Load Boundary: Spherical roller thrust bearings carry primary unidirectional axial thrust and may support simultaneous radial loads only within Fr ≤ 0.55 · Fa while maintaining minimum required axial load to prevent roller skidding.
29384 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 420 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 650 mm |
| Boundary Dimensions & Weight | Overall height (H) | 140 mm |
| Boundary Dimensions & Weight | Inner-ring width (B) | 48 mm |
| Boundary Dimensions & Weight | Outer-ring width (C) | 68 mm |
| Boundary Dimensions & Weight | Inner-ring rib / raceway diameter (d1) | 610 mm |
| Boundary Dimensions & Weight | Outer-ring rib / raceway diameter (D1) | 514.5 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 175 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Ca) | 3600 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Coa) | 16000 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 420 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 600 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 525 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 575 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 6 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 5 mm |
| Abutment & Fillet Dimensions | Axial offset (S) | 235 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Structural Geometry and Operating Boundaries
- Asymmetrical Barrel Rollers & Self-Alignment: Compensates for shaft deflection and housing misalignment up to approximately 1.5°–2° under heavy axial loads (load center offset S = 235 mm, d1 = 610 mm, D1 = 514.5 mm).
- Separable Shaft Washer & Housing Washer: Simplifies installation and inspection on massive vertical shafts (420 mm bore).
- Circulating Oil Lubrication Recommended: Reference limiting speed is 600 r/min (oil) and 420 r/min (grease); continuous industrial drives normally require circulating oil to remove flange-sliding friction heat.
Typical Heavy-Duty Industrial Applications
- Cement & Coal Vertical Roller Mills: Grinding table thrust support under extreme continuous axial load.
- Heavy Plastic & Rubber Screw Extruders: High-pressure axial thrust blocks paired with radial cylindrical roller bearings (Industrial Gearboxes Hub).
- Marine Propulsion, Hydro Turbines & Heavy Crane Hooks: Large vertical thrust assemblies requiring misalignment tolerance.
ISO Nominal Cross-Reference for 29384
| Brand | Nominal Designation | Boundary Dimensions (d × D × H) | Basis |
|---|---|---|---|
| ZQM Bearings | 29384 | 420 × 650 × 140 mm | ZQM 259-page General Catalogue |
| SKF | 29384 E | 420 × 650 × 140 mm | ISO 104 nominal dimensions |
| FAG / Schaeffler | 29384-E1-MB | 420 × 650 × 140 mm | ISO 104 nominal dimensions |
| NSK | 29384 M | 420 × 650 × 140 mm | ISO 104 nominal dimensions |
ISO Nominal Boundary Disclaimer: Cross-brand references reflect ISO 104 nominal boundary dimensions (420 × 650 × 140 mm) only and do not guarantee direct interchangeability. Confirm cage execution, oil flow grooves, and axial load ratings against factory drawings prior to ordering.
Mounting Abutment and ISO 281 Life Verification
Check shaft shoulder abutment da min = 525 mm, housing abutment Da max = 575 mm, and max fillet radius ra max = 5 mm. Verify combined axial/radial equivalent load (Pa = Fa + 1.2 · Fr when Fr ≤ 0.55 · Fa) using our ISO 281 Bearing Life Calculator.
Factory Quality Control and Export Logistics
Produced at Wafangdian Qunma Bearing Manufacturing Co., Ltd. (ISO 9001 & ISO 14001 certified) with Ningbo international engineering coordination and Shanghai heavy-crate export consolidation. Contact ZQM Bearings for factory drawing confirmation and quotation.
Frequently Asked Questions — 29384
What are the verified dimensions and weight of the 29384 thrust bearing?
29384 has a bore diameter d = 420 mm, outer diameter D = 650 mm, overall assembly height H = 140 mm, and a reference mass of 175 kg per ZQM Bearings’ catalog.
What is the maximum radial load allowed on 29384?
Per ISO 281, simultaneous radial load Fr must stay at or below 0.55 times axial load Fa (Fr ≤ 0.55 · Fa), and minimum axial load must be maintained during operation to prevent roller skidding.
Should 29384 be lubricated with circulating oil or grease?
Circulating oil lubrication (reference speed limit 600 r/min) is strongly preferred for continuous heavy-duty vertical mills and extruders to dissipate sliding heat at the guide flange; grease (420 r/min) is suited only for low-speed intermittent operation.
Are the catalog axial ratings Ca / C0a confirmed against factory drawings?
Yes. ZQM lists reference ratings of 3,600 kN / 16,000 kN from the 259-page catalog and confirms final axial load ratings, cage material, and tolerance details on the official factory order drawing prior to manufacturing.
How do I request lead time and export pricing for 29384?
Submit designation 29384, equipment type, required quantity, lubrication method, and destination port via our Contact page.




