51210 Thrust Ball Bearing 50 × 78 × 22 mm

ISO 104 Series 12 light single-direction flat-seat 51210 thrust ball bearing (50 × 78 × 22 mm, total height H = 22 mm) engineered for 10-ton overhead bridge crane hook blocks and hoist swivels under pure suspended vertical load (Fr = 0). Static/dynamic Ca & C0a confirmed on factory drawing.

The 51210 thrust ball bearing (50 × 78 × 22 mm, ISO 104 Dimension Series 12) steps up noticeably in ball diameter and ring thickness over the extra-light 51110 (50 × 70 × 14 mm) to carry suspended loads inside 10-ton overhead bridge crane hook blocks, electric wire-rope hoist swivels, and jib-crane forged hooks. Built exclusively for pure unidirectional vertical load (Fr = 0), its 22 mm total height (H) and three separable parts make statutory crane-hook inspections straightforward.

ISO 104 Specification Symbol 51210 Nominal Crane Hook Swivel Notes
Shaft Washer Bore d 50 mm Fits 50 mm forged hook shank
Housing Washer OD D 78 mm Sturdier Series 12 vs 70 mm on 51110
Total Height H 22 mm Thicker washers & larger balls than 51110
Permissible Load Axis Pure Vertical Axial Fr = 0 Unidirectional Zero radial capacity; zero angular tilt
Separable Maintenance 3-Piece Flat Seat Housing Bore D1 > 50 mm Never invert shaft & housing washers
Static/Dynamic Axial Ratings C0a / Ca / Cage Factory Drawing Verified Steel or brass cage & C0a confirmed at quote

51210 Hook-Block Swivel Performance & Statutory Inspection Ease

When riggers rotate a suspended steel plate or die block by hand under an overhead bridge crane, the entire lifted tonnage rests through the forged hook nut directly onto the thrust bearing seated inside the crosshead trunnion. A gritty or brinelled bearing forces operators to yank dangerously on suspended loads. Stepping up from 51110 to Series 12 51210 (78 mm OD, 22 mm height) provides deeper raceway grooves and larger balls to resist lifting shock without adding excessive hook-block bulk.

Because crane hooks undergo periodic non-destructive shank inspections mandated by plant safety rules, the 51210’s separable three-piece layout lets inspectors slide the shaft washer, ball-cage assembly, and housing washer completely off the crosshead, check the hook thread root, clean and regrease the raceways, and reassemble in minutes. Remember its rigid engineering scope: the crosshead bushing handles side-pull contact while the flat-seat 51210 takes strictly pure vertical pull (Fr = 0) with zero misalignment tolerance, and it is never rated for high-speed rotary spindles. Static and dynamic axial ratings (C0a / Ca), cage material (pressed steel vs solid brass), and inspection documentation options are confirmed on the ZQM factory print prior to order confirmation.

51210 Cross-Reference & Hoist Spares Verification

Overhead crane service contractors standardizing 5-ton to 16-ton hoist blocks frequently cross-check these ISO 104 Series 12 codes (legacy Chinese code 8210):

Brand / Code System ISO 104 Designation Hoist Block Verification Notes
ZQM Bearings 51210 Factory print verifies C0a/Ca, D1 bore & retainer
SKF 51210 Standard flat-seat Series 12; check steel vs M brass cage
FAG / Schaeffler 51210 Confirm machined trunnion flatness before fitment
NSK / NTN / KOYO 51210 Verify static safety factor against crane duty class
Legacy GB Code 8210 Former Chinese crane-hook blueprint code

Interchange Scope: Equivalency covers ISO 104 boundary dimensions (50 × 78 × 22 mm) exclusively. Raceway hardening profile, cage strength, and static axial load ratings C0a differ among manufacturers and require verification against crane hook-block engineering drawings before replacement.

Hook Crosshead Flatness, Washer Orientation & Dust Shielding

Inside foundries, fabrication bays, and heavy material-handling plants, weld spatter and grit settle into unshielded crane hook crossheads. Fitting a simple sheet-metal dust shroud over the hook nut and packing the 51210 thoroughly with adhesive EP2 lithium-complex grease prevents abrasive scoring and moisture rust.

Never rush hook reassembly: fit the close-bore 50 mm shaft washer tightly onto the rotating hook shank beneath the locknut, and seat the larger-bore housing washer (D1 > 50 mm) squarely atop the stationary crosshead face—reversing them rubs the hook shank and jams swivel rotation. Keep the crosshead bearing seat machined flat and perpendicular, maintain light nut seating so balls do not rattle loose under unloaded hook lowering, and remember that any bidirectional lifting-pushing device requires a 522/523/524 double-direction thrust bearing or QJ unit instead.

Requesting 51210 Quotations for Crane OEMs & Rigging MRO

Share your crane tonnage rating, hook shank diameter (50 mm nominal), preferred steel or machined brass cage, operating environment (indoor shop vs outdoor shipyard/foundry), and batch quantity. Our engineering desk returns a verified factory drawing confirming housing bore D1 and axial C0a/Ca values before production.

Request 51210 Crane-Hook Drawing & Quote

51210 Technical FAQ for Overhead Crane Hook Blocks

Related Selection & Comparison: Compare slim 14 mm height on the same 50 mm shaft via 51110 or heavier 60 mm crane hooks via 51312, and explore lifting equipment guides in Conveyors & Cranes.

Why choose 51210 over 51110 on a 10-ton crane hook with a 50 mm shank?

Although both fit a 50 mm hook shank, Series 12 51210 (78 mm OD, 22 mm height) uses substantially larger balls and heavier flat washers than extra-light 51110 (70 × 14 mm), delivering far stronger static axial capacity C0a against hoisting shocks.

Can a 51210 crane-hook bearing handle diagonal side-pulling of loads?

No. Flat-seat 51210 bearings carry strictly vertical axial load (Fr = 0) with zero misalignment tolerance. Side-pulling bends the hook shank, edge-loads the washers, and violates safe overhead crane operation.

Which 51210 washer sits on the crane crosshead and which spins with the hook nut?

The larger-bore housing washer (D1 > 50 mm) rests stationary on the crosshead so the hook shank turns cleanly inside it; the tight 50 mm shaft washer sits against the rotating hook locknut.

What legacy Chinese bearing number equals 51210?

Older Chinese bridge-crane and electric-hoist manuals designate the 50 × 78 × 22 mm 51210 thrust ball bearing as legacy code 8210.

Scroll to Top