Bulk Handling, Conveyors & Cranes

Heavy Bulk Handling, Conveyor Pulley and Port Crane Bearings

Built for port container gantry cranes, overland belt conveyor head pulleys, scraper conveyors, and bucket-wheel stacker-reclaimers. ZQM supplies heavy 232 / 231 / 222 / 241 spherical roller bearings, straight-bore NJ / NU cylindrical units, and drawing-based split-bearing solutions engineered for continuous outdoor service.

232 / 231 / 222Core Pulley Spherical Series
130–300 mmFeatured Bore Range on Page
ISO 15Radial Boundary Compliance
OEM / MROTrial Lots & Drawing-Based Split

Bearing Selection by Bulk Handling and Crane Position

Match belt conveyor pulleys, crane hoist winches, and yard reclaimers to verified ZQM roller bearing architectures.

232 series CA/W33 spherical roller bearing representative image for heavy conveyor head pulleys
Conveyor Head & Drive Pulleys

High-Tension Belt Conveyor Drive Pulleys

Overland and port terminal drive pulleys combine high belt tension with structural shaft bending and plummer-block mounting tolerances. Heavy 232 and 222 series CA/W33 spherical roller bearings accommodate shaft misalignment while delivering high radial load capacity.

NJ series cylindrical roller bearing representative image for port gantry crane hoist winches
Port Gantry Cranes & Hoist Winches

Crane Wire-Rope Drums, Sheaves and Winch Drives

Ship-to-shore container gantry cranes, shipyard jib cranes, and heavy hoist gearboxes run stop-start shock cycles under swinging loads. Straight-bore NJ (one-direction locating; pair with HJ angle ring or opposing unit for bidirectional control) and NU (floating) cylindrical rollers support winch drums and gear shafts cleanly.

Large-bore spherical roller bearing representative image for bucket-wheel stacker-reclaimers
Stacker-Reclaimers & Scraper Drives

Bucket-Wheel Reclaimers and Coal Yard Conveyors

Power-plant coal yards and ore terminals expose bucket-wheel shafts and heavy apron feeders to continuous dust, shock, and uneven loading. Large-bore 231 (optional 1:12 K) and wide-section 241 (optional 1:30 K30) spherical roller bearings provide dependable radial capacity and W33 relubrication channels.

222 series CA/W33 spherical roller bearing representative image for conveyor tail pulleys and plummer blocks
Plummer Blocks & Field Service

Tail Pulleys and Drawing-Based Split Solutions

Standard plummer-block pulleys frequently use 222 / 231 / 232 spherical units on straight shafts or 1:12 K adapter sleeves. For trapped pulley or drive shafts where removing couplings and reducers is impractical, ZQM evaluates custom split-bearing solutions strictly against your engineering drawing.

Verified Conveyor, Crane and Bulk Handling Bearing Matrix

Verified Specifications · ZQM Engineering Catalogue
Modeld × D × B (mm)Cr / C0r (kN)Mass (kg)Typical Position & Bore NoteDetails
23240 CA/W33200 × 360 × 1281,660 / 2,75057.1Conveyor bend / take-up pulley (straight; optional 1:12 K)View Specs
23244 CA/W33220 × 400 × 1442,020 / 3,40080.4Heavy belt conveyor head pulley (straight; optional 1:12 K)View Specs
23248 CA/W33240 × 440 × 1602,440 / 4,050106Overland high-tension drive pulley (straight; optional 1:12 K)View Specs
23148 CA/W33240 × 400 × 1281,790 / 3,10066.9Stacker-reclaimer boom drive (straight; optional 1:12 K)View Specs
23160 CA/W33300 × 500 × 1602,670 / 4,800125Bucket-wheel shaft & heavy pulley (straight; optional 1:12 K)View Specs
22252 CA/W33260 × 480 × 1302,180 / 3,400104Plummer-block tail / snub pulley (straight; optional 1:12 K)View Specs
22256 CA/W33280 × 500 × 1302,280 / 3,650110High-capacity conveyor pulley shaft (straight; optional 1:12 K)View Specs
24152 CA/W33260 × 440 × 1802,560 / 4,700109Wide-section low-speed drum (straight; optional 1:30 K30)View Specs
NJ228EM140 × 250 × 42395 / 5159.43Crane hoist gearbox shaft (Fw 169 mm, straight bore)View Specs
NJ326EM130 × 280 × 58615 / 73519.5Heavy winch pinion & drive shaft (Fw 167 mm, straight bore)View Specs

Nominal boundary dimensions conform to ISO 15. Standard spherical listings are straight cylindrical bore; where sleeve mounting is specified, 222 / 231 / 232 series use a 1:12 taper (K) while wide 241 series use a 1:30 taper (K30). NJ and NU cylindrical bearings use straight bores exclusively. Split-bearing assemblies are quoted strictly against customer drawings.

Harsh-Duty Engineering Notes for Bulk Handling and Port Cranes

Address shaft deflection, marine moisture, sleeve clearance loss, and locating/floating axial setups before installation.

1. Locating vs Floating Pulley Housings

Long conveyor pulley shafts expand axially under ambient sun and drive heat. Fix only one plummer-block housing with locating rings and leave the opposite spherical outer ring free to float axially—binding both housings induces severe parasitic axial load.

Read Spherical Series Selection Guide

2. Adapter Sleeve Clearance Reduction (1:12 K vs 1:30 K30)

When mounting 222 / 231 / 232 K bearings on H-series adapter sleeves, drive the inner ring up only until feeler-gauge clearance drops to the target residual range. Never mix 1:12 (K) sleeves with 1:30 (K30) tapered bores used in wide 240 / 241 series.

Read 1:12 K vs 1:30 K30 Mounting Guide

3. Coastal Salt Spray, Ore Dust and W33 Grease Purging

Port gantry cranes and open-pit transfer stations operate in abrasive dust and salt-laden air. Pair W33 outer-ring lubrication grooves and holes with taconite or labyrinth housing seals so fresh EP grease purges contaminants outward.

Read W33 Lubrication Groove Guide

4. Crane Hoist Pinion NJ / NU Axial Arrangement

In hoist winches, NU bearings accommodate shaft thermal elongation within their allowable axial displacement while NJ units locate in one direction—pair NJ with an opposing NJ or HJ angle ring where bidirectional axial positioning is required.

Read NJ / NU / NUP Axial Location Guide

Factory Coordination and Pre-Order Verification

Wafangdian manufacturing, Ningbo export coordination, and Shanghai warehouse support for OEM and port MRO teams.

ZQM large bearing ring CNC turning workshop in Wafangdian supporting heavy conveyor and crane bearings
Wafangdian Manufacturing & Order-Matched Inspection ZQM produces large-bore spherical and cylindrical roller bearings under ISO 9001 and ISO 14001 systems. Dimensional checks, radial internal clearance verification, and marking inspection are aligned to your purchase order; custom split-bearing drawings are reviewed by engineering before quoting.

Pre-Order Checklist for Conveyor and Crane Buyers

Share these five details to speed up technical confirmation and quotation:

  • Complete original designation or drawing (including straight bore vs 1:12 K / 1:30 K30 taper and adapter/withdrawal sleeve code)
  • Target radial internal clearance group (CN, C3, or C4) and plummer-block / housing series if applicable
  • Equipment station (head/tail pulley, gantry hoist winch, scraper drive, or stacker-reclaimer) and outdoor sealing environment
  • For split-bearing replacements: full shaft, housing, and axial envelope drawing for engineering feasibility check
  • Order quantity (MRO spare set, mixed container batch, or scheduled OEM supply) and required packing/inspection documents
Send Conveyor & Crane Inquiry

Frequently Asked Questions

Practical answers for port terminal maintenance engineers and bulk handling OEMs.

When should belt conveyor head pulleys use 232 series instead of 222 or 231 series spherical roller bearings?

Choose 232 series (such as 23244 CA/W33 or 23248 CA/W33) on high-tension overland drive pulleys and heavy bend pulleys where maximum radial load capacity and shock durability are required within a given shaft diameter. Use 222 series on moderate-load tail or snub pulleys where a narrower width fits standard plummer blocks, and 231 series where outer diameter is more constrained than width.

Do ZQM conveyor and crane bearings support tapered-bore adapter sleeves?

Standard catalog spherical roller bearings are straight bore, and tapered-bore executions can be specified for adapter or withdrawal sleeves. Remember that 222, 231, and 232 series use a 1:12 taper (K), whereas wide-section 240 and 241 series use a 1:30 taper (K30). Always confirm residual radial clearance with feeler gauges after sleeve drive-up.

Does ZQM supply split roller bearings for trapped conveyor or marine drive shafts?

Split-bearing assemblies are not treated as generic off-the-shelf catalog swaps. ZQM evaluates and supplies custom split-bearing solutions strictly against your engineering drawing, shaft envelope, load profile, and housing constraints—send your drawing via our Contact page for feasibility review.

How should NJ and NU cylindrical roller bearings be paired in port crane hoist winches?

Use NU bearings (such as NU228EM) at the non-locating end so shaft thermal expansion slides internally within the bearing’s allowable axial displacement, and use NJ bearings (such as NJ228EM or NJ326EM) for one-direction axial location—paired either with an opposing NJ unit or an HJ angle ring when bidirectional axial positioning is needed.

Bulk Handling & Crane Supply

Need Verified Conveyor Pulley or Port Crane Bearings?

Send your bearing list, sleeve designations, or custom split-bearing drawings. ZQM engineers confirm dimensions, radial clearance, and lead times directly from our factory coordination team.

Scroll to Top