Two-pole multistage boiler feedwater pumps spin long, stiff 110 mm shafts at 2,980 to 3,580 rpm while pumping 150 °C deaerated water into power-plant steam drums. Inside compact water-jacketed bearing brackets where outer housing diameter is tightly constrained, the ZQM 6022 deep groove ball bearing delivers an agile 110 × 170 × 28 mm light-series profile weighing just 2.09 kg, paired with 82 kN dynamic capacity (Cr), 73 kN static capacity (C0r), and high rotational velocity up to 3,800 rpm grease or 4,500 rpm oil.
6022 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 110 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 170 mm |
| Boundary Dimensions & Weight | Width (B) | 28 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 2.09 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 82 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 73 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 3800 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 4500 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 119 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 161 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 2.0 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2 mm |
| Calculation Factors | Calculation factor (f0) | 16 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
High-Speed Feedwater Pump Mechanics of the 6022
At 3,580 rpm on a 140 mm pitch diameter (dm · n ≈ 501,000 mm·rpm), centrifugal ball forces and churning drag dominate bearing temperature far more than pure radial gravity load:
- 4,500 rpm Oil-Lubricated Headroom: Smaller, lighter balls inside the 30 mm radial cross-section cut centrifugal spin losses dramatically compared with heavy 63-series equivalents, keeping 2-pole 60 Hz feedwater pumps comfortably inside their thermal envelope.
- Compact 170 mm Outer Envelope: Slim 28 mm width and 170 mm OD allow pump OEMs to place mechanical cartridge seals closer to the bearing span, raising rotor critical bending speed well above operating rpm.
- Residual Hydraulic Thrust Tracking (f0 = 16): Although multistage pumps rely on hydraulic balance drums or opposed impellers to cancel most axial force, wear-ring erosion steadily raises residual thrust. Calculation factor f0 = 16 governs the combined radial-axial rating boundary cleanly.
- Smooth Axial Float on Hot Shafts: High-temperature feedwater expands the pump shaft several tenths of a millimeter relative to the cool cast bracket; the non-locating 6022 slides freely in an H7/G7 bore to prevent thermal cross-locking.
ISO 15 Dimensional Cross-Reference Table for 6022
| Manufacturer | Reference Code | Bore d | OD D | Width B | Centrifugal Pump Context |
|---|---|---|---|---|---|
| ZQM | 6022 | 110 mm | 170 mm | 28 mm | Open light-series catalog base; C3/cage per order |
| SKF | 6022 / 6022/C3 | 110 mm | 170 mm | 28 mm | High-speed pump bracket standard |
| FAG / Schaeffler | 6022 / 6022-C3 | 110 mm | 170 mm | 28 mm | Low-friction ball-and-cage geometry |
| NSK | 6022 / 6022CM | 110 mm | 170 mm | 28 mm | Quiet electric-motor & pump execution |
| NTN / Koyo | 6022 | 110 mm | 170 mm | 28 mm | Standard ISO 10-series light section |
Dimension boundary note: Equivalency above applies purely to ISO 15 nominal dimensions (110 × 170 × 28 mm). Because high-speed pump brackets depend sensitively on cage balance, internal clearance (CN vs C3), and oil-ring immersion depth, confirm all suffix specifications against the pump OEM datasheet before procurement.
Boiler Feedwater Pump Bracket Lubrication & Mounting Playbook
- Precision Abutment Sizing: Turn the pump shaft shoulder to da ≥ 119 mm and machine the bracket housing shoulder to Da ≤ 161 mm, keeping shaft/housing fillet radii to ra ≤ 2 mm to clear the 2.0 mm minimum bearing chamfer without interference.
- Oil-Ring Bath or Pure Oil-Mist Above 3,000 rpm: At 3,580 rpm, grease life shortens rapidly. Maintain ISO VG 32 or VG 46 synthetic/turbine oil in a constant-level oiler (oil line set precisely at the center of the lowest rolling ball) or deploy pressurized oil-mist lubrication to avoid churning foam.
- Track Balance-Drum Wear Before Thrust Overloads the 6022: Monitor balance-line leak-off pressure and bearing housing temperature; once residual axial load exceeds ~25–30% of radial load continuously, inspect balance-drum clearances or evaluate paired 7022/7222 angular contact thrust bearings.
- Protect Against Steam-Seal Condensation: Failed mechanical seals spray hot boiler condensate straight toward the bearing isolator. Fit labyrinth bearing protectors instead of lip seals that score high-speed 110 mm sleeves.
Maintaining high-pressure boiler feedwater pumps, petrochemical process pumps, or turbo-blowers? Submit shaft rpm, oil system type, and required clearance grade via our pump bearing inquiry page for direct technical review.
Multistage Boiler Feedwater Pump 6022 Technical FAQ
Related Selection & Comparison: Need an ultra-thin radial envelope on the exact same 110 mm shaft? Compare the 16 mm wide 61822 thin-section ball bearing, or verify pump shaft pairing options in Angular Contact Ball Bearings.
Can a single 6022 run safely at 3,580 rpm on a 60 Hz boiler feedwater pump?
Yes—with oil lubrication (oil ring, circulating oil, or oil mist), the 6022 is rated up to 4,500 rpm. Even under grease lubrication its catalog ceiling is 3,800 rpm, though oil cooling is strongly preferred for continuous 24/7 boiler service above 3,000 rpm.
When is a 6022 insufficient for axial thrust on a multistage pump?
A 6022 handles light-to-moderate residual bidirectional thrust (evaluated using f0 = 16 and C0r = 73 kN) behind a healthy hydraulic balance drum. If the pump lacks a hydraulic balancing device or faces severe cavitation surge, pair angular contact bearings on the thrust end instead.
Why does overfilling a constant-level oiler make a 3,000 rpm 6022 run dangerously hot?
Submerging more than half the bottom ball forces the fast-moving ball complement to plow through dense oil, generating intense viscous shear heat and aeration. Keep static oil right at the lowest ball centerline.
Should both bearings in a hot feedwater pump be clamped axially in their housings?
Never clamp both ends. Lock only the locating end while allowing the opposing 6022 outer ring (170 mm OD) to slide axially inside a precision H7/G7 housing bore as the 150 °C pump shaft grows thermally.





