The 2212 self-aligning ball bearing (60 × 110 × 28 mm, ISO 15 Dimension Series 22) combines a generous 28 mm wide double-row footprint with minimal rotational drag, making it a preferred support on paper-mill wire-section guide rolls, felt return rolls, and high-speed film-converting web rollers. Supplied with a 60 mm straight bore or as 2212K (1:12 taper) pairing with an H312 sleeve for 55 mm shafting, plus optional -2RS seals for splash-prone wet ends.
| ISO 15 Dimension | Symbol | 2212 Nominal | Engineering Context |
|---|---|---|---|
| Bore Diameter | d | 60 mm | Straight journal fit |
| Outside Diameter | D | 110 mm | Identical OD to 1212 |
| Wide-Series Width | B | 28 mm | 6 mm wider than 1212 (22 mm) |
| Tapered & Sealed Options | 2212K / -2RS | 1:12 Taper / Dual Contact Seals | 2212K mounts on 55 mm shaft via H312 |
| Rolling Geometry | Double-Row Ball | Sphered Outer Ring | Ultra-low breakaway drag (p = 3) |
| Load Ratings & Cage | Cr / C0r / Cage | Factory Drawing Confirmed | Verified per corrosion/moisture spec at quote |
2212 Smooth Web Tracking & Roll-Sag Accommodation
Guide and tension rolls spanning 3 to 5 meters across paper-machine forming wires and slitter-rewinders deflect downward in the center under fabric wrap tension. Even more critically, idle web rollers are driven solely by friction from the moving forming fabric, wet tissue sheet, or thin polymer film. Any bearing drag spike causes micro-slippage that streaks the paper web, abrades expensive forming fabrics, or wrinkles packaging film.
The 2212 addresses both constraints simultaneously: its sphered outer raceway follows roll-end slope up to roughly 2.5° (open) without cramping, while its point-contact double-row balls exhibit far lower breakaway torque than heavier spherical roller units. Notice the clear duty separation inside a paper mill: while heavily loaded press rolls and steam-heated dryer cylinders demand 222xx/232xx spherical roller bearings, light-to-moderate wet-end guide rolls and dry converting idler rolls rely on the freer-spinning 2212. Retainer execution (stamped steel, machined brass, or polyamide up to ~120 °C) and formal load ratings are verified on the ZQM drawing at quotation.
2212 Cross-Reference & Paper-Machine Spares Mapping
Pulp-and-paper maintenance engineers reviewing mill roll lists routinely encounter these ISO 15 Series 22 numbers (alongside legacy Chinese blueprint code 1512):
| Manufacturer / Standard | Open Cylindrical | 1:12 Tapered / Sealed | Paper-Mill Verification Note |
|---|---|---|---|
| ZQM Bearings | 2212 | 2212K / 2212-2RS | Confirm water-resistant grease & cage on drawing |
| SKF | 2212 ETN9 | 2212 EKTN9 / 2212 E-2RS1TN9 | 2RS1 seals reduce allowable misalignment to ~1.5° |
| FAG / Schaeffler | 2212-TVH | 2212-K-TVH / 2212-2RS-TVH | Verify washdown compatibility & clearance |
| NSK / NTN | 2212 | 2212K / 2212LLU | Confirm retainer material and C3 fit if heated |
| Legacy GB Code | 1512 | 11512 | Historical Chinese code for 2212 series |
Interchange Boundary: Cross-referenced numbers verify 60 × 110 × 28 mm ISO 15 boundary fitment only. Seal drag, rust-inhibiting grease formulation, internal clearance, and dynamic capacities differ by manufacturer and require engineering sign-off before replacing OEM roll bearings.
Wet-End Washdown Protection & Moisture Barrier Practices
Water spray, white-water stock splashes, and acidic cleaning showers inside pulp, paper, and converting plants destroy standard mineral-greased bearings through rust pitting long before rolling fatigue occurs. Open 2212 units inside stainless or epoxy-coated housings should be purged with water-insoluble calcium-sulfonate or lithium-complex marine-grade grease behind double-labyrinth flingers.
For light converting idler rolls where relubrication lines are impractical, 2212-2RS sealed bearings simplify maintenance—just verify seal lip drag stays compatible with fragile tissue or thin foil webs, and keep roll deflection within the ~1.5° sealed-alignment window. For cantilevered or plain 55 mm guide-roll journals, 2212K mounted via an H312 sleeve accelerates roll changes during scheduled wire-change outages.
Ordering 2212 Bearings for Paper Mills & Converting OEMs
Share your roll position (wet-end forming section vs dry slitter-rewinder), bore version (60 mm straight 2212 vs 1:12 tapered 2212K + H312 sleeve), open vs -2RS sealed preference, clearance class (CN or C3), and quantity. We confirm the full drawing specification—including load ratings and grease options—before initiating production.
Request 2212 Paper-Mill Drawing & Quote
2212 Engineering Questions for Paper & Converting Rollers
Related Selection & Comparison: Compare slim 22 mm width via 1212 or larger 75 mm conveyor shafts via 2215, and explore belt-roller bearing guidance in our Conveyors & Cranes Hub.
Why choose 2212 over a 22212 spherical roller bearing on a forming-wire guide roll?
Guide rolls are driven solely by fabric contact and carry modest radial load. The 2212 spins with much lower rotational drag than a 22212 SRB, preventing forming-wire skidding while still absorbing roll sag.
What shaft size fits 2212K with an H312 adapter sleeve?
The 2212K (1:12 tapered bore) mounts onto a 55 mm plain roll journal using a metric H312 adapter sleeve, whose extra length matches the 28 mm wide inner ring.
Should wet-end guide rolls rely solely on 2212-2RS integral seals against washdown hoses?
No. Direct high-pressure washdown jets can penetrate single-lip bearing seals. Combine 2212 or 2212-2RS with external housing V-rings or labyrinth shields and water-resistant grease barriers.
Can 2212 operate on steam-heated paper dryer cylinders?
No. Heavy steam-heated dryer cylinders impose massive thermal growth, high temperatures, and extreme radial loads requiring large-bore spherical roller bearings (such as 230/231/232 series with C3/C4 clearance), not self-aligning ball bearings.



