Manufactured to ISO 12240-1 Dimension Series E, the GE50ES-2RS (GE 50 ES-2RS) radial spherical plain bearing accommodates a 50 mm pin bore inside a 75 mm outside diameter, with an inner-ring width (B) of 35 mm and an outer-ring width (C) of 28 mm. Featuring hardened bearing-steel sliding contact treated with phosphate and MoS₂, relubrication grooves and oil holes in both rings, and dual -2RS contact seals, it excels in mobile crane luffing cylinder trunnions and hydraulic outrigger stabilizer hinges subjected to sustained static boom-holding forces.
GE50ES-2RS ISO 12240-1 Nominal Boundary Dimensions
| Dimension / Feature | Verified Value | Notes |
|---|---|---|
| Designation | GE50ES-2RS | ISO 12240-1 Dimension Series E, sealed radial spherical plain bearing |
| Bore Diameter (d) | 50 mm | Nominal hinge pin diameter |
| Outside Diameter (D) | 75 mm | Nominal cylinder clevis / housing eye bore |
| Inner Ring Width (B) | 35 mm | Spherical ball width between spacer cheeks |
| Outer Ring Width (C) | 28 mm | Single-fractured outer ring width |
| Sliding Interface | Hardened steel-on-steel | Phosphate + MoS₂ surface finish; periodic EP grease relubrication |
| Seals & Relubrication | -2RS double-lip seals + ES grooves | Contact seals on both faces; annular lubrication grooves & holes in both rings |
| Ratings, Clearance & Tilt Angle | Confirmed on factory drawing | Dynamic/static sliding capacities, radial clearance group & coating verified upon quotation |
Static Boom-Holding Mechanics, p·v Wear & 90° Split Placement
Mobile truck cranes and all-terrain lifting rigs frequently hold suspended loads stationary for extended intervals while slewing or positioning steelwork. Unlike rolling joints that suffer indentation under prolonged static dwell, the GE50ES-2RS spreads clamping pressure across a broad conforming spherical steel-on-steel contact area. Wear life is dictated by specific contact pressure × sliding velocity (p·v) during slow luffing adjustments combined with disciplined EP grease purging that prevents stick-slip chatter when the cylinder breaks static friction.
The outer ring incorporates a single radial assembly fracture. Crane cylinder technicians must orient this radial fracture precisely at 90° to the primary hydraulic compression axis before pressing the bearing home; keeping the split in the unloaded neutral zone preserves spherical roundness under heavy static boom moments.
Mobile Crane Luffing Cylinder & Outrigger Stabilizer Deployment
Outrigger stabilizer jack pivots and telescopic boom luffing eyes live permanently outdoors—exposed to rain, road salt spray, and jobsite concrete dust—while deflecting elastically as crane counterweights swing 360°. The 7 mm width offset between inner ring (35 mm) and outer ring (28 mm) grants generous angular misalignment freedom, preventing structural chassis twist from transferring destructive side bending into hydraulic cylinder rods.
Double-lip -2RS elastomer seals lock water and airborne grit out of the 50 mm hinge while permitting periodic fresh EP grease injection through the outer-ring groove to flush spent lubricant cleanly. For hydraulic cylinder OEMs and fleet lifting-equipment rebuilders, ZQM coordinates dimensional stability across repeat production lots. Browse heavy lifting and mobile machinery support on our industrial equipment overview.
GE50ES-2RS International Brand Cross-Reference
| Manufacturer / Code | Reference Equivalent | ISO 12240-1 Series E Alignment (50 × 75 × 35/28 mm) |
|---|---|---|
| ZQM / GB/T 9163 | GE50ES-2RS | Hardened steel/steel, phosphate/MoS₂ treated, relubrication holes, -2RS seals |
| SKF | GE 50 ES-2RS | Steel-on-steel radial spherical plain bearing with twin lip seals |
| INA / Schaeffler | GE50-DO-2RS | Series E maintenance-type steel-on-steel (DO), double-sided lip seals |
| IKO | GE50ES-2RS | ISO Series E steel-on-steel sealed spherical plain bearing |
| Fluro | GE 50 ES-2RS | Steel-on-steel relubricatable joint with -2RS lip seals |
Interchangeability Statement: Listed designations align strictly on nominal ISO 12240-1 Series E external boundaries (50 × 75 × 35/28 mm). Internal radial clearance group (C2/CN/C3), lip-seal weatherability, phosphate/MoS₂ coating thickness, and sliding load ratings vary by producer and must be confirmed via ZQM factory drawing before critical lifting-equipment installation.
Ordering GE50ES-2RS for Crane OEMs & Hydraulic Service Depots
When requesting a GE50ES-2RS factory quote, note your cylinder eye press-fit tolerance (determining CN vs. C3 radial clearance), operating climate temperature range (cold-weather outdoor crane operation), and required batch size. Every formal ZQM quotation includes a confirmed engineering drawing detailing sliding capacities, clearance limits, and surface treatment. Connect with our export engineering team through our contact & quotation portal.
GE50ES-2RS Crane & Hydraulic Hinge FAQ
Related Selection & Comparison: Evaluate neighboring crane and equipment pivot sizes GE40ES-2RS and GE60ES-2RS, explore Conveyors & Cranes, or browse all Spherical Plain Bearings.
Why is GE50ES-2RS chosen for crane luffing cylinders that hold static loads for long periods?
Its conforming steel-on-steel spherical sliding surface distributes heavy static boom weight across a wide contact patch without concentrated point indentation, while allowing self-aligning articulation as the crane chassis flexes under suspended loads.
What is the correct orientation for the GE50ES-2RS outer-ring fracture during cylinder overhaul?
Position the single radial fracture in the outer ring at 90° to the primary hydraulic cylinder load line. Never place the split directly along the compressive boom-holding axis, where peak force can distort the outer ring and bind the joint.
How often should a -2RS sealed GE50ES-2RS crane hinge be relubricated?
Relubrication frequency depends on lifting duty cycle, ambient weather exposure, and p·v sliding severity. Follow the crane OEM maintenance schedule to purge fresh MoS₂-fortified EP grease through the ES lubrication groove until clean lubricant refreshes the seal lips.
Does ZQM provide formal factory drawings with sliding load ratings for GE50ES-2RS before purchase?
Yes. Because exact dynamic and static sliding load ratings, radial clearance group, tilt angle, and coating specs are model-specific, ZQM issues a confirmed factory drawing upon quotation for both trial repair orders and OEM cylinder contracts.



