The 2210 self-aligning ball bearing (50 × 90 × 23 mm, ISO 15 Dimension Series 22) expands the ring width by 3 mm over narrow 1210 while preserving the exact same 50 mm bore and 90 mm housing diameter. That wider double-row track brings higher load-carrying margin to food-processing screw conveyors and sawmill edger feed-roll plummer blocks without forcing housing redesign. Order straight 50 mm bore or 2210K (1:12 taper) matched with an ISO 2982-1 H310 adapter sleeve for 45 mm bar shafts.
| ISO 15 Series 22 Field | Symbol | 2210 Nominal Spec | Conveyor / Sawmill Context |
|---|---|---|---|
| Cylindrical Bore | d | 50 mm | Direct fit on 50 mm machined stub shaft |
| Outside Diameter | D | 90 mm | Matches SNL 510-608 / SN 510 housing bore |
| Wide Series Width | B | 23 mm | 3 mm wider than 1210 (20 mm) for added capacity |
| 1:12 Tapered Execution | 2210K | 1:12 Taper (K) | Requires H310 sleeve on 45 mm shaft (not H210) |
| Self-Alignment Geometry | Sphered Outer Track | ~2.5° – 3° (Open) | Point-contact balls; sealed 2RS reduces tilt angle |
| Ratings, Seals & Cage | Cr / C0r / 2RS / Cage | Confirmed on Factory Print | Issued per open/sealed & grease spec at quote |
2210 Wide-Section Advantage Over 1210 in Screw Augers & Edger Rolls
Welded stainless screw-conveyor troughs in starch, flour, and pet-food plants rarely stay dead straight once bolted to mezzanine steelwork, and timber edger infeed tables absorb continual bark-slap vibration as green lumber enters the saw gang. In both settings, maintenance engineers often run out of radial space around a 90 mm bearing seat yet need sturdier life than a slim 20 mm-wide 1210 delivers. Moving up to the 23 mm-wide 2210 keeps the identical 90 mm housing bore while widening the ball spread for improved radial and light combined axial stability.
Open 2210 assemblies articulate freely across roughly 2.5° to 3° inside their spherical outer track, neutralizing welded-trough twist effortlessly. Because wood resin, sawdust, and food washdown moisture threaten open raceways, buyers frequently evaluate integral contact-lip 2210-2RS sealed variants pre-filled with suitable grease (noting that integral rubber seals narrow the permissible misalignment angle slightly compared with open designs). Final dynamic/static load capacities, open vs sealed availability, and cage material are confirmed on ZQM’s engineering drawing at quotation.
2210 Brand Equivalency & Sleeve Pairing Check (H310 vs H210)
Food-plant and lumber-mill buyers cross-checking 50 × 90 × 23 mm replacements should confirm both the 23 mm width and the wide-series H310 sleeve (never the shorter H210 used on narrow 1210K):
| Manufacturer / Standard | Straight Bore | 1:12 Tapered Bore | Ordering & Seal Verification |
|---|---|---|---|
| ZQM Bearings | 2210 | 2210K | 23 mm width; open or 2RS & cage confirmed on print |
| SKF | 2210 ETN9 / 2210 E-2RS1TN9 | 2210 EKTN9 / 2210 E-2RS1KTN9 | 2RS1 = contact seals; TN9 = polyamide cage |
| FAG / Schaeffler | 2210-TVH / 2210-2RS-TVH | 2210-K-TVH / 2210-2RS-K-TVH | Verify open grease-purge vs sealed execution |
| NSK / NTN | 2210 | 2210K | Confirm seal suffix (2RS/LLB) & clearance grade |
| Legacy GB Code | 1510 | 11510 | Older Chinese blueprint code for Series 22 |
Dimensional Boundary Disclaimer: Cross-listed codes match ISO 15 envelope dimensions (50 × 90 × 23 mm) exclusively. Seal lip elastomer chemistry, H1 food-grade grease fill, cage material, and load ratings vary across suppliers and must be confirmed against original machinery specifications.
Washdown Hygiene, Sawdust Exclusion & H310 Mounting Discipline
Across timber processing lines and bulk screw-conveyor handling systems, premature bearing death stems mostly from contamination rather than steel fatigue. On wet food-conveyor end plates, pair open 2210 bearings inside sealed pillow housings with food-grade H1 water-resistant grease and periodic purge flushes, or opt for 2RS sealed versions protected behind auxiliary washdown deflectors. On sawmill edger feed rolls, pitch-laden sawdust cakes around exposed seals; external felt-and-labyrinth combinations inside SNL 510 housings shed wood fibers cleanly.
When mounting 2210K onto an unstepped 45 mm conveyor drive shaft, use the full-length H310 adapter sleeve so the tapered bore seats squarely across all 23 mm of ring width. Remember that severe slab-impact sawmill breakdown rolls exceeding ball-bearing shock margins should transition to 22210 spherical roller bearings sharing the same 50 × 90 × 23 mm ISO footprint.
Ordering 2210 Bearings for Conveyor OEMs & Timber Mill MRO
Provide five details when requesting a quotation: straight 50 mm bore vs 2210K + H310 sleeve, open vs 2RS sealed preference, lubricant/washdown condition (standard EP2 vs H1 food-compatible), cage material (steel or polyamide), and order quantity. ZQM engineering validates every dimensional and rating specification on a signed drawing before shipment.
Request 2210 Engineering Print & Pricing
2210 Selection Questions for Conveyors & Sawmill Rolls
Related Selection & Comparison: Compare narrow 20 mm 1210 or larger 60 mm 2212, check H310 1:12 sleeve clearance in our Tapered Bore Calculator, decode 2RS/TN9 codes in the Bearing Suffix Decoder, or browse Self-Aligning Ball Bearings.
Can a 2210 directly replace a 1210 in an existing 90 mm plummer block?
Both share 50 mm bore and 90 mm OD, but 2210 is 23 mm wide versus 20 mm for 1210. Verify housing pocket width and locating-ring thickness before upgrading so the extra 3 mm does not bind the end covers.
Why does 2210K require an H310 adapter sleeve rather than an H210 sleeve?
Because 2210K is 23 mm wide (Series 22), it requires the longer ISO 2982-1 H310 sleeve to support the full tapered bore length on a 45 mm shaft; the shorter H210 fits only narrow 20 mm 1210K bearings.
Should food-processing screw conveyors use open 2210 or sealed 2210-2RS bearings?
Sealed 2210-2RS units simplify maintenance and keep splash moisture out at moderate shaft angles, whereas open 2210 units inside sealed SNL housings allow full ~2.5°–3° alignment and periodic grease purging during high-pressure washdowns.
Does adding 2RS rubber seals reduce the misalignment capacity of a 2210?
Yes. Contact rubber lips ride against the inner ring shoulder, so sealed 2210-2RS variants allow noticeably less angular tilt (typically around 1.5°) than open 2210 bearings (~2.5°–3°).
When should a sawmill feed roll upgrade from 2210 to a 22210 spherical roller bearing?
Both share the exact 50 × 90 × 23 mm boundary envelope; upgrade to 22210 whenever heavy cant drops, shock jams, or high radial pinch loads exceed point-contact ball fatigue limits.



