294 SERIES · SPHERICAL ROLLER THRUST BEARING
294/500 Spherical Roller Thrust Bearing Dimensions & Specifications
294/500 spherical roller thrust bearing: 500 mm bore (d), 870 mm outside diameter (D), 224 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 500 mm |
|---|---|
| Outside diameter D | 870 mm |
| Total height H | 224 mm |
| Housing washer height C | 107 mm |
| Mass | 589 kg |
| Catalogue dynamic load Ca | 7850 kN |
| Catalogue static load Coa | 33000 kN |
| Grease-lubricated speed | 320 rpm |
| Oil-lubricated speed | 460 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 750 mm |
|---|---|
| Abutment dimension da | 670 mm |
| Minimum chamfer r12 | 9.5 mm |
| Diameter D1 | 648 mm |
| Diameter d1 | 790 mm |
| Maximum fillet ra | 8 mm |
| Offset S | 290 mm |
| Shaft washer height B | 81 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 90394/500 | ZQM Catalogue P.256 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 294/500?
The 294/500 catalogue lists da min = 670 mm; Da max = 750 mm; ra max = 8 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 294/500?
The listed values for 294/500 are grease: 320 rpm; oil: 460 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 294/500?
The catalogue reference mass for 294/500 is 589 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 294/500 spherical roller thrust bearing?
294/500 (500 × 870 × 224 mm, total height H = 224 mm and housing washer height C = 107 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 238/500CAF3/W33 | Spherical Roller Bearing | 500 × 620 × 90 mm |
| 618/500F1 | Deep Groove Ball Bearing | 500 × 620 × 56 mm |
Compare alternative series sharing the same 500 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 294/500
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

