294 SERIES · SPHERICAL ROLLER THRUST BEARING
29496 Spherical Roller Thrust Bearing Dimensions & Specifications
29496 spherical roller thrust bearing: 480 mm bore (d), 850 mm outside diameter (D), 224 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 480 mm |
|---|---|
| Outside diameter D | 850 mm |
| Total height H | 224 mm |
| Housing washer height C | 108 mm |
| Mass | 545 kg |
| Catalogue dynamic load Ca | 7200 kN |
| Catalogue static load Coa | 31000 kN |
| Oil-lubricated speed | 340 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 730 mm |
|---|---|
| Abutment dimension da | 645 mm |
| Minimum chamfer r12 | 9.5 mm |
| Diameter D1 | 638 mm |
| Diameter d1 | 810 mm |
| Maximum fillet ra | 8 mm |
| Offset S | 280 mm |
| Shaft washer height B | 81 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29496?
The 29496 catalogue lists da min = 645 mm; Da max = 730 mm; ra max = 8 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29496?
The listed values for 29496 are oil: 340 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29496?
The catalogue reference mass for 29496 is 545 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29496 spherical roller thrust bearing?
29496 (480 × 850 × 224 mm, total height H = 224 mm and housing washer height C = 108 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 23896CAF3/W33 | Spherical Roller Bearing | 480 × 600 × 90 mm |
| 61896 | Deep Groove Ball Bearing | 480 × 600 × 56 mm |
Compare alternative series sharing the same 480 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29496
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

