294 SERIES · SPHERICAL ROLLER THRUST BEARING

294/560 Spherical Roller Thrust Bearing Dimensions & Specifications

294/560 spherical roller thrust bearing: 560 mm bore (d), 980 mm outside diameter (D), 250 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 560 mmD 980 mmH 250 mmCr 9600 kNMass 800 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 560D 980H 250Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d560 mm
Outside diameter D980 mm
Total height H250 mm
Housing washer height C124 mm
Mass800 kg
Catalogue dynamic load Ca9600 kN
Catalogue static load Coa42000 kN
Oil-lubricated speed300 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da835 mm
Abutment dimension da755 mm
Minimum chamfer r1212 mm
Diameter D1744 mm
Diameter d1935 mm
Maximum fillet ra10 mm
Offset S325 mm
Shaft washer height B91 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code90394/560ZQM Catalogue P.256

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 294/560?

The 294/560 catalogue lists da min = 755 mm; Da max = 835 mm; ra max = 10 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 294/560?

The listed values for 294/560 are oil: 300 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 294/560?

The catalogue reference mass for 294/560 is 800 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 294/560 spherical roller thrust bearing?

294/560 (560 × 980 × 250 mm, total height H = 250 mm and housing washer height C = 124 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 560 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
238/560CAF3/W33Spherical Roller Bearing560 × 680 × 90 mm
618/560F1Deep Groove Ball Bearing560 × 680 × 56 mm
NJ18/560Cylindrical Roller Bearing560 × 680 × 56 mm
NU28/560Cylindrical Roller Bearing560 × 680 × 72 mm

Compare alternative series sharing the same 560 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 294/560

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top