294 SERIES · SPHERICAL ROLLER THRUST BEARING
294/600 Spherical Roller Thrust Bearing Dimensions & Specifications
294/600 spherical roller thrust bearing: 600 mm bore (d), 1030 mm outside diameter (D), 258 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 600 mm |
|---|---|
| Outside diameter D | 1030 mm |
| Total height H | 258 mm |
| Housing washer height C | 127 mm |
| Mass | 895 kg |
| Catalogue dynamic load Ca | 10100 kN |
| Catalogue static load Coa | 43000 kN |
| Oil-lubricated speed | 280 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 885 mm |
|---|---|
| Abutment dimension da | 800 mm |
| Minimum chamfer r12 | 12 mm |
| Diameter D1 | 780 mm |
| Diameter d1 | 985 mm |
| Maximum fillet ra | 10 mm |
| Offset S | 345 mm |
| Shaft washer height B | 93 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 90394/600 | ZQM Catalogue P.256 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 294/600?
The 294/600 catalogue lists da min = 800 mm; Da max = 885 mm; ra max = 10 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 294/600?
The listed values for 294/600 are oil: 280 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 294/600?
The catalogue reference mass for 294/600 is 895 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 294/600 spherical roller thrust bearing?
294/600 (600 × 1030 × 258 mm, total height H = 258 mm and housing washer height C = 127 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| NU18/600 | Cylindrical Roller Bearing | 600 × 730 × 60 mm |
| NU28/600 | Cylindrical Roller Bearing | 600 × 730 × 78 mm |
Compare alternative series sharing the same 600 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 294/600
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

