294 SERIES · SPHERICAL ROLLER THRUST BEARING

294/710 Spherical Roller Thrust Bearing Dimensions & Specifications

294/710 spherical roller thrust bearing: 710 mm bore (d), 1220 mm outside diameter (D), 308 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 710 mmD 1220 mmH 308 mmCr 14300 kNMass 1500 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 710D 1220H 308Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d710 mm
Outside diameter D1220 mm
Total height H308 mm
Housing washer height C148 mm
Mass1500 kg
Catalogue dynamic load Ca14300 kN
Catalogue static load Coa65500 kN
Oil-lubricated speed220 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da1050 mm
Abutment dimension da950 mm
Minimum chamfer r1215 mm
Diameter D1920 mm
Diameter d11160 mm
Maximum fillet ra12 mm
Offset S407 mm
Shaft washer height B132 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code90394/710ZQM Catalogue P.257

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 294/710?

The 294/710 catalogue lists da min = 950 mm; Da max = 1050 mm; ra max = 12 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 294/710?

The listed values for 294/710 are oil: 220 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 294/710?

The catalogue reference mass for 294/710 is 1500 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 294/710 spherical roller thrust bearing?

294/710 (710 × 1220 × 308 mm, total height H = 308 mm and housing washer height C = 148 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 710 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
618/710F1Deep Groove Ball Bearing710 × 870 × 74 mm
NU18/710Cylindrical Roller Bearing710 × 870 × 74 mm

Compare alternative series sharing the same 710 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 294/710

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top