294 SERIES · SPHERICAL ROLLER THRUST BEARING

294/750 Spherical Roller Thrust Bearing Dimensions & Specifications

294/750 spherical roller thrust bearing: 750 mm bore (d), 1280 mm outside diameter (D), 315 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 750 mmD 1280 mmH 315 mmCr 15100 kNMass 1680 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 750D 1280H 315Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d750 mm
Outside diameter D1280 mm
Total height H315 mm
Housing washer height C152 mm
Mass1680 kg
Catalogue dynamic load Ca15100 kN
Catalogue static load Coa69000 kN
Mounting dimensions & additional parameters (8)
Abutment dimension Da1105 mm
Abutment dimension da995 mm
Minimum chamfer r1215 mm
Diameter D1970 mm
Diameter d11220 mm
Maximum fillet ra12 mm
Offset S429 mm
Shaft washer height B128 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code90394/750ZQM Catalogue P.257

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 294/750?

The 294/750 catalogue lists da min = 995 mm; Da max = 1105 mm; ra max = 12 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What is the reference mass of 294/750?

The catalogue reference mass for 294/750 is 1680 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What are the main dimensions and load ratings of 294/750?

In the ZQM General Catalogue, 294/750 has nominal boundary dimensions of Array. Catalog load ratings: Ca 15100 kN, C0a 69000 kN. Confirm exact clearance, cage design and tolerance class against your drawing prior to ordering.

What lubrication and minimum load rules apply to 294/750 spherical roller thrust bearing?

294/750 (750 × 1280 × 315 mm, total height H = 315 mm and housing washer height C = 152 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 750 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
238/750CAF3/W33Spherical Roller Bearing750 × 920 × 128 mm
618/750F1Deep Groove Ball Bearing750 × 920 × 78 mm
NU18/750Cylindrical Roller Bearing750 × 920 × 78 mm

Compare alternative series sharing the same 750 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 294/750

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top