294 SERIES · SPHERICAL ROLLER THRUST BEARING

29440 Spherical Roller Thrust Bearing Dimensions & Specifications

29440 spherical roller thrust bearing: 200 mm bore (d), 400 mm outside diameter (D), 122 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 200 mmD 400 mmH 122 mmCr 2290 kNMass 83.5 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 200D 400H 122Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d200 mm
Outside diameter D400 mm
Total height H122 mm
Housing washer height C56.7 mm
Mass83.5 kg
Catalogue dynamic load Ca2290 kN
Catalogue static load Coa8150 kN
Grease-lubricated speed600 rpm
Oil-lubricated speed800 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da335 mm
Abutment dimension da290 mm
Minimum chamfer r125 mm
Diameter D1267.5 mm
Diameter d1360 mm
Maximum fillet ra4 mm
Offset S122 mm
Shaft washer height B44 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039440ZQM Catalogue P.253

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29440?

The 29440 catalogue lists da min = 290 mm; Da max = 335 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29440?

The listed values for 29440 are grease: 600 rpm; oil: 800 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29440?

The catalogue reference mass for 29440 is 83.5 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29440 spherical roller thrust bearing?

29440 (200 × 400 × 122 mm, total height H = 122 mm and housing washer height C = 56.7 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 200 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
61840MADeep Groove Ball Bearing200 × 250 × 24 mm

Compare alternative series sharing the same 200 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29440

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top