294 SERIES · SPHERICAL ROLLER THRUST BEARING

29438 Spherical Roller Thrust Bearing Dimensions & Specifications

29438 spherical roller thrust bearing: 190 mm bore (d), 380 mm outside diameter (D), 115 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 190 mmD 380 mmH 115 mmCr 2100 kNMass 75.6 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 190D 380H 115Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d190 mm
Outside diameter D380 mm
Total height H115 mm
Housing washer height C53.7 mm
Mass75.6 kg
Catalogue dynamic load Ca2100 kN
Catalogue static load Coa7450 kN
Grease-lubricated speed630 rpm
Oil-lubricated speed850 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da320 mm
Abutment dimension da275 mm
Minimum chamfer r125 mm
Diameter D1263 mm
Diameter d1345 mm
Maximum fillet ra4 mm
Offset S117 mm
Shaft washer height B41 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039438ZQM Catalogue P.253

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29438?

The 29438 catalogue lists da min = 275 mm; Da max = 320 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29438?

The listed values for 29438 are grease: 630 rpm; oil: 850 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29438?

The catalogue reference mass for 29438 is 75.6 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29438 spherical roller thrust bearing?

29438 (190 × 380 × 115 mm, total height H = 115 mm and housing washer height C = 53.7 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 190 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
NU2838MCylindrical Roller Bearing190 × 240 × 30 mm

Compare alternative series sharing the same 190 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29438

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top