294 SERIES · SPHERICAL ROLLER THRUST BEARING

29448 Spherical Roller Thrust Bearing Dimensions & Specifications

29448 spherical roller thrust bearing: 240 mm bore (d), 440 mm outside diameter (D), 122 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 240 mmD 440 mmH 122 mmCr 2420 kNMass 96.1 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 240D 440H 122Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d240 mm
Outside diameter D440 mm
Total height H122 mm
Housing washer height C60 mm
Mass96.1 kg
Catalogue dynamic load Ca2420 kN
Catalogue static load Coa9100 kN
Grease-lubricated speed560 rpm
Oil-lubricated speed750 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da375 mm
Abutment dimension da330 mm
Minimum chamfer r126 mm
Diameter D1316 mm
Diameter d1400 mm
Maximum fillet ra5 mm
Offset S142 mm
Shaft washer height B43 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039448ZQM Catalogue P.254

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29448?

The 29448 catalogue lists da min = 330 mm; Da max = 375 mm; ra max = 5 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29448?

The listed values for 29448 are grease: 560 rpm; oil: 750 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29448?

The catalogue reference mass for 29448 is 96.1 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29448 spherical roller thrust bearing?

29448 (240 × 440 × 122 mm, total height H = 122 mm and housing washer height C = 60 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 240 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
61848MADeep Groove Ball Bearing240 × 300 × 28 mm

Compare alternative series sharing the same 240 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29448

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top