294 SERIES · SPHERICAL ROLLER THRUST BEARING
29452 Spherical Roller Thrust Bearing Dimensions & Specifications
29452 spherical roller thrust bearing: 260 mm bore (d), 480 mm outside diameter (D), 132 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 260 mm |
|---|---|
| Outside diameter D | 480 mm |
| Total height H | 132 mm |
| Housing washer height C | 63 mm |
| Mass | 101.5 kg |
| Catalogue dynamic load Ca | 2820 kN |
| Catalogue static load Coa | 10700 kN |
| Grease-lubricated speed | 500 rpm |
| Oil-lubricated speed | 670 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 405 mm |
|---|---|
| Abutment dimension da | 360 mm |
| Minimum chamfer r12 | 6 mm |
| Diameter D1 | 346 mm |
| Diameter d1 | 445 mm |
| Maximum fillet ra | 5 mm |
| Offset S | 154 mm |
| Shaft washer height B | 86 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 9039452 | ZQM Catalogue P.254 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 29452?
The 29452 catalogue lists da min = 360 mm; Da max = 405 mm; ra max = 5 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29452?
The listed values for 29452 are grease: 500 rpm; oil: 670 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29452?
The catalogue reference mass for 29452 is 101.5 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29452 spherical roller thrust bearing?
29452 (260 × 480 × 132 mm, total height H = 132 mm and housing washer height C = 63 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 23852CA/W33 | Spherical Roller Bearing | 260 × 320 × 45 mm |
| 61852MA | Deep Groove Ball Bearing | 260 × 320 × 28 mm |
Compare alternative series sharing the same 260 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29452
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

