294 SERIES · SPHERICAL ROLLER THRUST BEARING

29484 Spherical Roller Thrust Bearing Dimensions & Specifications

29484 spherical roller thrust bearing: 420 mm bore (d), 730 mm outside diameter (D), 185 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 420 mmD 730 mmH 185 mmCr 6650 kNMass 323 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 420D 730H 185Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d420 mm
Outside diameter D730 mm
Total height H185 mm
Housing washer height C90.5 mm
Mass323 kg
Catalogue dynamic load Ca6650 kN
Catalogue static load Coa27500 kN
Oil-lubricated speed430 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da630 mm
Abutment dimension da560 mm
Minimum chamfer r127.5 mm
Diameter D1545 mm
Diameter d1665 mm
Maximum fillet ra6 mm
Offset S244 mm
Shaft washer height B67 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039484ZQM Catalogue P.255

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29484?

The 29484 catalogue lists da min = 560 mm; Da max = 630 mm; ra max = 6 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29484?

The listed values for 29484 are oil: 430 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29484?

The catalogue reference mass for 29484 is 323 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29484 spherical roller thrust bearing?

29484 (420 × 730 × 185 mm, total height H = 185 mm and housing washer height C = 90.5 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 420 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23884CA/W33Spherical Roller Bearing420 × 520 × 75 mm
NU3884MCylindrical Roller Bearing420 × 520 × 75 mm

Compare alternative series sharing the same 420 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29484

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top