23260 CA/W33 Spherical Roller Bearing 300 × 540 × 192 mm

Large-bore 23260 CA/W33 spherical roller bearing (300 × 540 × 192 mm, Cr 3,400 kN, C0r 5,900 kN, 189 kg) with cylindrical bore and W33 outer-ring lubrication groove and oil holes. Engineered by ZQM Bearings for crushers, mills, and heavy industrial drives.

SKU: 23260 CA/W33 Category:

Request a Quote

23260 CA/W33 Heavy Industrial Gearbox Output Shaft Bearing Overview

Spanning a 300 mm bore inside a 300 × 540 × 192 mm footprint (189 kg), the 23260 CA/W33 spherical roller bearing anchors low-speed, ultra-high-torque output shafts in planetary wind-class reducers, sugar-mill drives, and steel rolling-mill pinion stands. Verified catalog capacity reaches Cr = 3,400 kN and C0r = 5,900 kN (e = 0.35, Y1 = 1.9, Y2 = 2.9, Y0 = 1.9).

Helical gear separation forces generate simultaneous radial and axial loads; the 23260 geometry handles both directions cleanly inside circulating ISO VG 320–460 gear-oil sumps.

23260CA/W33 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 23260CA/W33
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)300 mm
Boundary Dimensions & WeightOutside diameter (D)540 mm
Boundary Dimensions & WeightWidth (B)192 mm
Boundary Dimensions & WeightReference mass (Weight)189 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)3400 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)5900 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)480 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)630 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)322 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)518 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)5 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)4 mm
Calculation FactorsCalculation factor (e)0.35
Calculation FactorsAxial load factor (static) (Y0)1.9
Calculation FactorsAxial load factor (Y1)1.9
Calculation FactorsAxial load factor (Y2)2.9

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Gearbox Drive Engineering Characteristics

  • Combined Helical Gear Thrust Handling: Y1 = 1.9 and Y2 = 2.9 axial factors allow stable operation under heavy single-helical mesh loads.
  • Circulating Oil Sump Compatibility: W33 outer-ring oil groove aligns directly with pressurized gearbox housing galleries (oil speed limit 630 r/min; grease 480 r/min).
  • Thermal Clearance Stability: Heavy gearboxes run with warm shafts relative to air-cooled split casings; specifying C3 clearance maintains safe hot operating clearance.

Heavy Reducer & Power Transmission Equipment

Standard on cement mill main reducers, rubber Banbury mixer drives, sugar-cane mill gearboxes, and steel coiler output shafts. Review complete drivetrain bearing combinations in our Industrial Gearboxes Hub and decode OEM gearbox suffixes using our Bearing Suffix Decoder.

Nominal ISO Cross-Reference (23260 Series)

Manufacturer Nominal Reference Dimensions
ZQM Bearings 23260 CA/W33 300 × 540 × 192 mm
SKF 23260 CAK/W33 (taper) / CA/W33 300 × 540 × 192 mm
FAG / Schaeffler 23260-B-MB / E1-XL 300 × 540 × 192 mm
NSK / NTN 23260 CAME4 / 23260 B D1 300 × 540 × 192 mm

Engineering Disclaimer: Listed equivalents cover ISO nominal 300 × 540 × 192 mm boundary geometry only—verify gear-casing fit tolerances, oil viscosity, and clearance against OEM drawings.

Gearbox Housing Abutments & Factory Supply

Confirm shaft shoulder da min = 322 mm, casing shoulder Da max = 518 mm, and max fillet ra max = 4 mm. Tapered-bore executions use a 1:12 K taper (H3260 / AH3260). Produced at our ISO 9001/14001 Wafangdian plant. Submit gearbox bearing BOM for quotation.

23260 CA/W33 Industrial Gearbox FAQ

Can 23260 CA/W33 support both radial and helical axial loads in a reducer?

Yes. With Cr = 3,400 kN and ISO factors e = 0.35, Y1 = 1.9, Y2 = 2.9, it readily carries heavy combined radial and bidirectional axial gear forces.

Why is C3 clearance widely specified for 300 mm gearbox output shafts?

Tight shaft press fits plus the temperature differential between oil-heated shafts and air-cooled gear casings reduce internal clearance; C3 prevents thermal preload.

Does 23260 work with splash or pressurized ISO VG 320 gear oil?

Yes. The W33 outer-ring groove and oil holes allow pressurized oil injection or splash entry directly between roller rows up to 630 r/min.

What bore taper applies if a reducer requires a tapered 23260 K?

The 232 series uses a 1:12 tapered bore (suffix K, H3260/AH3260 sleeves), distinct from the 1:30 K30 taper on 240/241 series.

What should OEM gearbox rebuilders provide for an accurate ZQM quote?

Send complete designation, straight vs K bore, clearance (CN/C3/C4), quantity, and delivery port via our Contact page.

Scroll to Top