23260 CA/W33 Heavy Industrial Gearbox Output Shaft Bearing Overview
Spanning a 300 mm bore inside a 300 × 540 × 192 mm footprint (189 kg), the 23260 CA/W33 spherical roller bearing anchors low-speed, ultra-high-torque output shafts in planetary wind-class reducers, sugar-mill drives, and steel rolling-mill pinion stands. Verified catalog capacity reaches Cr = 3,400 kN and C0r = 5,900 kN (e = 0.35, Y1 = 1.9, Y2 = 2.9, Y0 = 1.9).
Helical gear separation forces generate simultaneous radial and axial loads; the 23260 geometry handles both directions cleanly inside circulating ISO VG 320–460 gear-oil sumps.
23260CA/W33 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 300 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 540 mm |
| Boundary Dimensions & Weight | Width (B) | 192 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 189 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 3400 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 5900 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 480 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 630 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 322 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 518 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 5 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 4 mm |
| Calculation Factors | Calculation factor (e) | 0.35 |
| Calculation Factors | Axial load factor (static) (Y0) | 1.9 |
| Calculation Factors | Axial load factor (Y1) | 1.9 |
| Calculation Factors | Axial load factor (Y2) | 2.9 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Gearbox Drive Engineering Characteristics
- Combined Helical Gear Thrust Handling: Y1 = 1.9 and Y2 = 2.9 axial factors allow stable operation under heavy single-helical mesh loads.
- Circulating Oil Sump Compatibility: W33 outer-ring oil groove aligns directly with pressurized gearbox housing galleries (oil speed limit 630 r/min; grease 480 r/min).
- Thermal Clearance Stability: Heavy gearboxes run with warm shafts relative to air-cooled split casings; specifying C3 clearance maintains safe hot operating clearance.
Heavy Reducer & Power Transmission Equipment
Standard on cement mill main reducers, rubber Banbury mixer drives, sugar-cane mill gearboxes, and steel coiler output shafts. Review complete drivetrain bearing combinations in our Industrial Gearboxes Hub and decode OEM gearbox suffixes using our Bearing Suffix Decoder.
Nominal ISO Cross-Reference (23260 Series)
| Manufacturer | Nominal Reference | Dimensions |
|---|---|---|
| ZQM Bearings | 23260 CA/W33 | 300 × 540 × 192 mm |
| SKF | 23260 CAK/W33 (taper) / CA/W33 | 300 × 540 × 192 mm |
| FAG / Schaeffler | 23260-B-MB / E1-XL | 300 × 540 × 192 mm |
| NSK / NTN | 23260 CAME4 / 23260 B D1 | 300 × 540 × 192 mm |
Engineering Disclaimer: Listed equivalents cover ISO nominal 300 × 540 × 192 mm boundary geometry only—verify gear-casing fit tolerances, oil viscosity, and clearance against OEM drawings.
Gearbox Housing Abutments & Factory Supply
Confirm shaft shoulder da min = 322 mm, casing shoulder Da max = 518 mm, and max fillet ra max = 4 mm. Tapered-bore executions use a 1:12 K taper (H3260 / AH3260). Produced at our ISO 9001/14001 Wafangdian plant. Submit gearbox bearing BOM for quotation.
23260 CA/W33 Industrial Gearbox FAQ
Can 23260 CA/W33 support both radial and helical axial loads in a reducer?
Yes. With Cr = 3,400 kN and ISO factors e = 0.35, Y1 = 1.9, Y2 = 2.9, it readily carries heavy combined radial and bidirectional axial gear forces.
Why is C3 clearance widely specified for 300 mm gearbox output shafts?
Tight shaft press fits plus the temperature differential between oil-heated shafts and air-cooled gear casings reduce internal clearance; C3 prevents thermal preload.
Does 23260 work with splash or pressurized ISO VG 320 gear oil?
Yes. The W33 outer-ring groove and oil holes allow pressurized oil injection or splash entry directly between roller rows up to 630 r/min.
What bore taper applies if a reducer requires a tapered 23260 K?
The 232 series uses a 1:12 tapered bore (suffix K, H3260/AH3260 sleeves), distinct from the 1:30 K30 taper on 240/241 series.
What should OEM gearbox rebuilders provide for an accurate ZQM quote?
Send complete designation, straight vs K bore, clearance (CN/C3/C4), quantity, and delivery port via our Contact page.






