,

6028 Deep Groove Ball Bearing 140 × 210 × 33 mm

Large-bore ISO 60-series 6028 deep groove ball bearing (140 × 210 × 33 mm, 3.25 kg) delivering 110 kN dynamic capacity and 3,600 rpm oil speed for hydro/steam turbine auxiliary generators and large industrial blower shafts.

Request a Quote

Hydro and steam turbine auxiliary synchronous generators, exciter shafts, and high-volume induced-draft industrial blowers rely on rigid 140 mm forged shafts spinning smoothly at 1,500 to 3,000 rpm—yet radial rotor loads remain moderate enough that heavy roller bearings waste kilowatts in churning drag. Engineered in the slim ISO 60 light series at 140 × 210 × 33 mm and only 3.25 kg, the ZQM 6028 deep groove ball bearing balances 110 kN dynamic capacity (Cr) and 109 kN static rating (C0r) with brisk speed limits of 3,000 rpm grease and 3,600 rpm oil.

6028 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 6028
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)140 mm
Boundary Dimensions & WeightOutside diameter (D)210 mm
Boundary Dimensions & WeightWidth (B)33 mm
Boundary Dimensions & WeightReference mass (Weight)3.25 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)110 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)109 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)3000 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)3600 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)149 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)201 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)2.0 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)2 mm
Calculation FactorsCalculation factor (f0)16

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Low-Torque High-DN Mechanics of the Large-Bore 6028

At a 175 mm pitch diameter turning 3,000 rpm (dm · n = 525,000 mm·rpm), minimizing parasitic friction and maintaining rolling traction across a large bore become primary design goals:

  • 3,000 / 3,600 rpm Speed Capability on a 140 mm Bore: Lightweight 33 mm cross-section and reduced ball mass suppress centrifugal skidding forces, enabling direct 2-pole 50 Hz (3,000 rpm) and 60 Hz (3,600 rpm oil-lubricated) auxiliary generator operation.
  • Lower Parasitic Frictional Losses Than Roller Alternatives: Point-contact deep groove kinematics run markedly cooler and consume less mechanical drive power than comparable cylindrical or spherical roller units under light-to-moderate rotor weight.
  • Axial Rotor Stability via f0 = 16: Precision ground raceways hold generator magnetic centers and blower aerodynamic balance steady in either axial direction, governed by calculation factor f0 = 16.
  • Slim 35 mm Radial Wall Envelope: Fitting a 140 mm shaft inside a 210 mm OD keeps pedestal castings compact and eases retrofit inside tight turbine exciter hoods.

ISO 15 Nominal Cross-Reference Table for 6028

Brand Base Designation d (mm) D (mm) B (mm) Power & Blower Application Note
ZQM 6028 140 210 33 Open light-series catalog baseline; C3/cage per order
SKF 6028 / 6028/C3 140 210 33 High-speed Explorer ball-and-cage profile
FAG / Schaeffler 6028 / 6028-C3 140 210 33 Low-friction generator & fan series
NSK / NTN 6028 / 6028C3 140 210 33 Pressed steel or machined brass M-cage options
Koyo / JTEKT 6028 140 210 33 Standard ISO 10-series large-bore execution

Boundary reference disclaimer: Brand designations share the ISO 15 nominal envelope (140 × 210 × 33 mm) solely for dimensional lookup. Because high-DN generator shafts depend tightly on cage material, radial clearance (CN vs C3), and low-noise raceway finish, verify full OEM suffix codes before interchange.

Turbine Exciter & Large Blower 6028 Commissioning Checklist

  • Machine Exact Large-Bore Abutments: Turn shaft shoulders to da ≥ 149 mm and pedestal bore abutments to Da ≤ 201 mm, holding fillet radii strictly to ra ≤ 2 mm to clear the 2.0 mm minimum bearing chamfer without seating interference.
  • Guard Against Light-Load Skidding at 3,000 rpm: On ultra-light exciter rotors spinning near 3,000 rpm, insufficient radial load lets balls slide rather than roll cleanly. Verify radial weight meets minimum load guidance or apply calibrated light axial spring preload on the floating end.
  • Allow Axial Expansion Along Hot Turbine Shafts: Steam-side auxiliary shafts expand thermally relative to cool concrete-mounted pedestals. Lock only the locating 6028 while mounting the floating end in a smooth H7/G7 bore so the 210 mm outer ring glides freely without inducing axial cross-bind.
  • Match Lubricant Strategy to Speed Band: At 1,500 rpm industrial blower duty, high-speed polyurea/lithium-complex grease works reliably; near 3,000–3,600 rpm turbine generator speed, transition to filtered ISO VG 32–46 circulating oil or metered oil-air lubrication to cap temperature rise.

Upgrading power-station exciter bearings or large industrial induced-draft fan shafts? Send rotor mass, rpm, and lubrication type via our ZQM power-generation bearing desk for verified C3 and cage quotes.

Turbine Auxiliary Generator & Large Blower 6028 FAQ

Related Selection & Comparison: Explore adjacent large-bore industrial ball bearings including 6324 and 670 mm 618/670 F1, or decode C3/M/Z/2RS suffixes in our Bearing Suffix Decoder.

Why select a 6028 ball bearing instead of a cylindrical roller bearing on a 140 mm generator shaft?

When radial rotor weight is modest compared with the 110 kN rating and speed runs 1,500–3,600 rpm, the 6028 runs with lower friction torque, avoids roller-end flange drag, and locates the shaft axially in both directions without needing a separate thrust bearing.

Can the 6028 run continuously at 3,600 rpm on a 60 Hz auxiliary generator?

Yes under circulating oil or oil-mist lubrication (catalog oil limit is 3,600 rpm), provided rotor balance is tight, C3 thermal clearance is verified, and minimum load prevents high-speed ball skidding. Grease lubrication caps at 3,000 rpm.

What happens if the floating-end 6028 sticks inside its 210 mm housing bore?

Thermal lengthening of a warm turbine or induced-draft flue-gas blower shaft builds massive unintended axial thrust across both bearings, spiking temperature within minutes and causing rapid fatigue spalling on opposite raceway shoulders.

Why does the 6028 have a higher f0 factor (16) than heavier 63-series bearings (13)?

Light-series 60-series bearings pack a larger number of smaller-diameter balls around the 175 mm pitch circle relative to ball size, shifting the ISO static-to-axial load geometry factor f0 upward to 16 for combined-load calculations.

Scroll to Top