294 SERIES · SPHERICAL ROLLER THRUST BEARING

294/630 Spherical Roller Thrust Bearing Dimensions & Specifications

294/630 spherical roller thrust bearing: 630 mm bore (d), 1090 mm outside diameter (D), 280 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 630 mmD 1090 mmH 280 mmCr 11600 kNMass 1100 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 630D 1090H 280Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d630 mm
Outside diameter D1090 mm
Total height H280 mm
Housing washer height C136 mm
Mass1100 kg
Catalogue dynamic load Ca11600 kN
Catalogue static load Coa51500 kN
Oil-lubricated speed260 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da935 mm
Abutment dimension da845 mm
Minimum chamfer r1212 mm
Diameter D1830 mm
Diameter d11040 mm
Maximum fillet ra10 mm
Offset S365 mm
Shaft washer height B100 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code90394/630ZQM Catalogue P.256

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 294/630?

The 294/630 catalogue lists da min = 845 mm; Da max = 935 mm; ra max = 10 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 294/630?

The listed values for 294/630 are oil: 260 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 294/630?

The catalogue reference mass for 294/630 is 1100 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 294/630 spherical roller thrust bearing?

294/630 (630 × 1090 × 280 mm, total height H = 280 mm and housing washer height C = 136 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 630 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
238/630CAF3/W33Spherical Roller Bearing630 × 780 × 112 mm
248/630CAF3/W33Spherical Roller Bearing630 × 780 × 150 mm
618/630F1Deep Groove Ball Bearing630 × 780 × 69 mm

Compare alternative series sharing the same 630 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 294/630

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top