294 SERIES · SPHERICAL ROLLER THRUST BEARING

294/850 Spherical Roller Thrust Bearing Dimensions & Specifications

294/850 spherical roller thrust bearing: 850 mm bore (d), 1440 mm outside diameter (D), 355 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 850 mmD 1440 mmH 355 mmCr 18700 kNMass 2350 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 850D 1440H 355Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d850 mm
Outside diameter D1440 mm
Total height H355 mm
Housing washer height C172 mm
Mass2350 kg
Catalogue dynamic load Ca18700 kN
Catalogue static load Coa99000 kN
Mounting dimensions & additional parameters (8)
Abutment dimension Da1270 mm
Abutment dimension da1160 mm
Minimum chamfer r1215 mm
Diameter D11034 mm
Diameter d11250 mm
Maximum fillet ra12 mm
Offset S507 mm
Shaft washer height B142 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code90394/850ZQM Catalogue P.257

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 294/850?

The 294/850 catalogue lists da min = 1160 mm; Da max = 1270 mm; ra max = 12 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What is the reference mass of 294/850?

The catalogue reference mass for 294/850 is 2350 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What are the main dimensions and load ratings of 294/850?

In the ZQM General Catalogue, 294/850 has nominal boundary dimensions of Array. Catalog load ratings: Ca 18700 kN, C0a 99000 kN. Confirm exact clearance, cage design and tolerance class against your drawing prior to ordering.

What lubrication and minimum load rules apply to 294/850 spherical roller thrust bearing?

294/850 (850 × 1440 × 355 mm, total height H = 355 mm and housing washer height C = 172 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 850 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
238/850CAF3/W33Spherical Roller Bearing850 × 1030 × 136 mm
618/850F1Deep Groove Ball Bearing850 × 1030 × 82 mm
NU28/850Cylindrical Roller Bearing850 × 1030 × 106 mm

Compare alternative series sharing the same 850 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 294/850

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top